View All Items

Title: A LOW PHASE NOISE K-BAND OSCILLATOR UTILIZING AN EMBEDDED DIELECTRIC RESONATOR ON MULTILAYER HIGH FREQUENCY LAMINATES.
Creator: Subramanian, Ajay, Gong, Xun, University of Central Florida
Abstract / Description: K-Band (18 to 26 GHz) dielectric resonator oscillators are typically used as a local oscillator in most K-Band digital transmitter/receiver topologies. Traditionally, the oscillator itself is made up of an active device, a dielectric resonator termination network, and a passive load matching network. The termination network embodies a cylindrical high permittivity dielectric resonator that is coupled on the same plane as a current carrying transmission line. This configuration provides an...
Show moreK-Band (18 to 26 GHz) dielectric resonator oscillators are typically used as a local oscillator in most K-Band digital transmitter/receiver topologies. Traditionally, the oscillator itself is made up of an active device, a dielectric resonator termination network, and a passive load matching network. The termination network embodies a cylindrical high permittivity dielectric resonator that is coupled on the same plane as a current carrying transmission line. This configuration provides an adequate resonance needed for oscillation but has some limitations. In order to provide a high Q resonance the entire oscillator is placed in a metal box to prevent radiation losses. This increases the overall size of the device and makes it difficult to integrate in smaller transceiver topologies. Secondly, a tuning screw is required to help excite the dominant mode of the resonator to achieve the high Q response. This can cause problems in precision due to the mechanical jitter of the screw inherent in mobile devices. By embedding this resonator inside the substrate it is possible to realize a very high Q resonance at a desired frequency and remove the need for a metal cavity and tuning screw. An additional advantage can be seen in terms of overall size reduction of the oscillator circuit. To demonstrate the feasibility of utilizing a dielectric resonator embedded within a substrate, a K-Band oscillator proof of concept has been designed, fabricated, and tested. The oscillator is comprised of a low noise active transistor device, an embedded k-band dielectric resonator and a passive transmission line load network. All elements within the oscillator are optimized to produce a steady oscillation near 20 GHz. Preliminary investigations of a microstrip resonator S-band (2-3 GHz) oscillator are first discussed. Secondly, various challenges in design and fabrication are discussed. Thereafter, simulated and measured results of the embedded DRO structure are presented. Emphasis is placed on output oscillation power and low phase noise. With further development, the entire oscillator can be embedded within the substrate leaving only the active device on the surface. This allows for a considerable reduction in material cost and simple integration with miniaturized digital transmitter/receiver devices.
Show less
Date Issued: 2008
Identifier: CFE0002451, ucf:47718
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0002451

Title: A RADAR INTERROGATOR FOR WIRELESS PASSIVE TEMPERATURE SENSING.
Creator: Lambert, Jeffrey, Gong, Xun, University of Central Florida
Abstract / Description: In this thesis I explore radio detection and ranging (RADAR) and software defined radio (SDR) in the context of wireless passive sensor interrogation. A RADAR topology is selected based upon preliminary measurements using ordinary laboratory instrumentation and then used for construction of a prototype X-band wireless measurement system using commercial, off-the-shelf (COTS) components. This research explores the feasibility of wireless passive sensor interrogation through practical...
Show moreIn this thesis I explore radio detection and ranging (RADAR) and software defined radio (SDR) in the context of wireless passive sensor interrogation. A RADAR topology is selected based upon preliminary measurements using ordinary laboratory instrumentation and then used for construction of a prototype X-band wireless measurement system using commercial, off-the-shelf (COTS) components. This research explores the feasibility of wireless passive sensor interrogation through practical application of SDR and RADAR techniques to the interrogation of a wireless passive resonator signal. This work serves as a foundation for further research on sensor interrogation through establishment of critical system parameters in the design of wireless measurement systems.
Show less
Date Issued: 2011
Identifier: CFE0003631, ucf:48886
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003631

Title: THE RELEVANCE OF TIME-TO-DIGITAL CONVERTERS TO SMALL PLATFORM DIRECTION FINDING SYSTEMS.
Creator: Nelson, Paul, Gong, Xun, University of Central Florida
Abstract / Description: This thesis explores a Time-Difference-of-Arrival (TDOA) approach to radio direction finding, utilizing picosecond-resolution Time-to-Digital Converters (TDCs). By measuring the relative time of arrival of a pulsed RF signal impinging on an antenna array, direction of arrival (DOA) can be ascertained. This technology enables versatile DOA calculation on platforms only several meters in length, and offers various size, weight, power, and cost advantages when compared to present DF technologies...
Show moreThis thesis explores a Time-Difference-of-Arrival (TDOA) approach to radio direction finding, utilizing picosecond-resolution Time-to-Digital Converters (TDCs). By measuring the relative time of arrival of a pulsed RF signal impinging on an antenna array, direction of arrival (DOA) can be ascertained. This technology enables versatile DOA calculation on platforms only several meters in length, and offers various size, weight, power, and cost advantages when compared to present DF technologies. A short baseline S-band TDOA DF system utilizing TDCs is designed, fabricated, and tested in a laboratory environment. This research suggests that such a DF system based on TDCs provides sufficient accuracy and precision to resolve Angle-of-Arrival (AOA) within several degrees.
Show less
Date Issued: 2010
Identifier: CFE0003115, ucf:48649
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003115

Title: WIRELESSLY SENSING RESONATE FREQUENCY OF PASSIVE RESONATORS WITH DIFFERENT Q VALUES.
Creator: Lukacs, Mathew, Gong, Xun, University of Central Florida
Abstract / Description: Numerous techniques exist for measuring temperature using passive devices such as SAW filters. However, SAW filters have a significant limitation regarding high temperature environments exceeding 1000C. There are several applications for a high temperature sensor in this range, most notably heat flux or temperature in turbine engines. For these environments, an alternative to SAW filters is to use a passive resonator. The resonate frequency will vary depending on the environment temperature....
Show moreNumerous techniques exist for measuring temperature using passive devices such as SAW filters. However, SAW filters have a significant limitation regarding high temperature environments exceeding 1000C. There are several applications for a high temperature sensor in this range, most notably heat flux or temperature in turbine engines. For these environments, an alternative to SAW filters is to use a passive resonator. The resonate frequency will vary depending on the environment temperature. Understanding how the frequency changes with temperature will allow us to determine the environmental temperature. In order for this approach to work, it is necessary to induce resonance in the device and measure the resonance frequency. However, the extreme high temperature makes wired connections impractical, therefore wireless interrogation is necessary. To be practical a system of wireless interrogation of up to 20cm is desired.
Show less
Date Issued: 2011
Identifier: CFE0003709, ucf:48828
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003709

Title: SAW Correlator Temperature Compensation Using a Pulse Width Modulated Temperature Controller.
Creator: Betancourt, Daniel, Weeks, Arthur, Malocha, Donald, Richie, Samuel, Gong, Xun, University of Central Florida
Abstract / Description: A Surface Acoustic Wave (SAW) correlator built on a Lithium Niobate substrate is temperature compensated in order to maintain a constant center frequency. Frequency shifts as a result of temperature variations limit device performance. An Arduino(&)#174;-based PWM temperature controller is developed to read the device temperature from a resistance temperature detector located on the SAW wafer and to regulate its temperature to a specified setpoint by providing current to a heater which is co...
Show moreA Surface Acoustic Wave (SAW) correlator built on a Lithium Niobate substrate is temperature compensated in order to maintain a constant center frequency. Frequency shifts as a result of temperature variations limit device performance. An Arduino(&)#174;-based PWM temperature controller is developed to read the device temperature from a resistance temperature detector located on the SAW wafer and to regulate its temperature to a specified setpoint by providing current to a heater which is co-located with the temperature sensor on the SAW correlator substrate. The final temperature controller achieves frequency shifts of 0.013 MHz from room temperature with a worst-case PPM experienced over 30(&)deg;C of temperature variation of 0.48 PPM/(&)deg;C. Linear and non-linear plant models are developed successfully to predict the device's temperature based on any input setpoint. Although there are alternatives to limit temperature drift at different temperatures, this thesis presents a simple method that works on a standard Lithium Niobate substrate.
Show less
Date Issued: 2019
Identifier: CFE0007787, ucf:52331
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007787

Title: Electromagnetic Environment in Payload Fairing Cavities.
Creator: Trout, Dawn, Wahid, Parveen, Wu, Xinzhang, Gong, Xun, Tang, Philip, University of Central Florida
Abstract / Description: An accurate determination of a spacecraft's radio frequency electromagnetic field environment during launch and flight is critical for mission success. Typical fairing structures consist of a parabolic nose and a cylindrical core with diameters of 1 to 5 meters resulting in electrically large dimensions for typical operational sources at S, C and X band where the free space wavelength varies from 0.15 m to 0.03 m. These electrically large size and complex structures at present have internal...
Show moreAn accurate determination of a spacecraft's radio frequency electromagnetic field environment during launch and flight is critical for mission success. Typical fairing structures consist of a parabolic nose and a cylindrical core with diameters of 1 to 5 meters resulting in electrically large dimensions for typical operational sources at S, C and X band where the free space wavelength varies from 0.15 m to 0.03 m. These electrically large size and complex structures at present have internal fairing electromagnetic field evaluation that is limited to general approximation methods and some test data. Though many of today's computational electromagnetic tools can model increasingly complex and large structures, they still have many limitations when used for field determination in electrically large cavities. In this dissertation, a series of test anchored, full wave computational electromagnetic models along with a novel application of the equivalent material property technique are presented to address the electrical, geometrical, and boundary constraints for electromagnetic field determination in composite fairing cavity structures and fairings with acoustic blanketing layers. Both external and internal excitations for these fairing configurations are examined for continuous wave and transient sources. A novel modification of the Nicholson Ross Weir technique is successfully applied to both blanketed aluminum and composite fairing structures and a significant improvement in computational efficiency over the multilayered model approach is obtained. The advantages and disadvantages of using commercially available tools by incorporating Multilevel Fast Multipole Method (MLFMM) and higher order method of moments (HO MoM) to extend their application of MoM to electrically large objects is examined for each continuous wave transmission case. The results obtained with these models are compared with those obtained using approximation techniques based on the Q factor, commonly utilized in the industry, and a significant improvement is seen in a prediction of the fields in these large cavity structures. A statistical distribution of data points within the fairing cavity is examined to study the nature of the fairing cavity field distribution and the effect of the presence of a spacecraft load on these fields is also discussed. In addition, a model with external application of Green's function is examined to address the shielding effectiveness of honeycomb panels in a fairing cavity. Accurate data for lightning induced effects within a fairing structure is not available and hence in this dissertation, a transmission line matrix method model is used to examine induced lightning effects inside a graphite composite fairing structure. The simulated results are compared with test data and show good agreement.
Show less
Date Issued: 2012
Identifier: CFE0004275, ucf:49505
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004275

Title: Synchronous Communication System for SAW Sensors Interrogation.
Creator: Troshin, Maxim, Malocha, Donald, Jones, W, Gong, Xun, University of Central Florida
Abstract / Description: During past two decades a variety of SAW based wireless sensors were invented and research is still in progress. As different frequencies, varied bandwidths, coding techniques and constantly changing post processing algorithms are being implemented, there is a constant need for a universal and adjustable synchronous communication system able to interrogate new generations of SAW sensors. This thesis presents the design of a multiple FPGA based communication system with an operational...
Show moreDuring past two decades a variety of SAW based wireless sensors were invented and research is still in progress. As different frequencies, varied bandwidths, coding techniques and constantly changing post processing algorithms are being implemented, there is a constant need for a universal and adjustable synchronous communication system able to interrogate new generations of SAW sensors. This thesis presents the design of a multiple FPGA based communication system with an operational frequency range of 450MHz-2.2GHz capable of producing user programmed modulated signal. The synchronous receiver is designed to have interchangeable chip, replacement of which would allow adjustment of the receiver's bandwidth. Within this paper the performance of the system is only evaluated at 915MHz centered 20MHz bandwidth region. An OFC temperature sensor was interrogated. Post-processing algorithms, measurement results, and proposals for the future use of the system are presented. Detailed overview of the structure and performance of every functional block along with design considerations are analyzed. Previously designed Matlab based software was adapted for post processing of the received signal. New software with simplified GUI was designed for programming of the desired signal.
Show less
Date Issued: 2012
Identifier: CFE0004270, ucf:49543
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004270

Title: Electrical Parasitic Bandwidth Limitations of Oxide-Free Lithographic Vertical-Cavity Surface-Emitting Lasers.
Creator: Yang, Xu, Deppe, Dennis, Fathpour, Sasan, Wu, Shintson, Gong, Xun, University of Central Florida
Abstract / Description: Nowadays, Vertical-Cavity Surface-Emitting Lasers (VCSELs) are the most popular optical sources in short-reach data communications. In the commercial oxide VCSEL technology, an oxide aperture is created inside resonant cavity in realizing good mode and current confinement, however, high electrical resistance comes along with forming the oxide aperture and the electrical parasitic bandwidth becomes the main limitation in modulation speed. In this report, electrical bandwidths of oxide-free...
Show moreNowadays, Vertical-Cavity Surface-Emitting Lasers (VCSELs) are the most popular optical sources in short-reach data communications. In the commercial oxide VCSEL technology, an oxide aperture is created inside resonant cavity in realizing good mode and current confinement, however, high electrical resistance comes along with forming the oxide aperture and the electrical parasitic bandwidth becomes the main limitation in modulation speed. In this report, electrical bandwidths of oxide-free lithographic VCSELs have been studied along with their general lasing properties. Due to the new ways of fabricating the aperture, record low resistances have been achieved in oxide-free lithographic VCSELs with various sizes, while high slope efficiencies and high output powers have been maintained. High speed simulation has been performed showing the very low differential resistances will benefit much to the electrical parasitic bandwidths, and are expected to produce higher modulation speed. A bottom emitting structure has been proposed and analyzed, showing reduction in both mirror resistance and capacitance will further improve the modulation speed. The total 3-dB modulation bandwidth is expected to be 50-80 GHz, much higher than the bandwidth reached in existing oxide VCSELs. Lithographic VCSELs also show superior lasing characteristics, including record low thermal resistance and record high output power. The maximum power exceeds 19 mW in a 6 (&)#181;m device and over 50 % power conversion efficiency has been achieved. A maximum single mode operation power of 5 mW has been observed from a 1 (&)#181;m diameter VCSEL. High temperature stress testing has been performed showing lithographic VCSELs can operate more reliably than oxide VCSELs under extreme operating conditions. Lithographic VCSEL with low electrical resistance, single-mode operation, high efficiency, and high power will be a strong candidate as the optical source in high speed data communications, as well as other applications such as high power VCSEL arrays and optical sensing.
Show less
Date Issued: 2016
Identifier: CFE0006425, ucf:51491
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0006425

Title: High Temperature Materials Characterization and Sensor Application.
Creator: Ren, Xinhua, Gong, Xun, Wahid, Parveen, Wu, Xinzhang, An, Linan, University of Central Florida
Abstract / Description: This dissertation presents new solutions for turbine engines in need of wireless temperature sensors at temperatures up to 1300oC. Two important goals have been achieved in this dissertation. First, a novel method for precisely characterizing the dielectric properties of high temperature ceramic materials at high temperatures is presented for microwave frequencies. This technique is based on a high-quality (Q)-factor dielectrically-loaded cavity resonator, which allows for accurate...
Show moreThis dissertation presents new solutions for turbine engines in need of wireless temperature sensors at temperatures up to 1300oC. Two important goals have been achieved in this dissertation. First, a novel method for precisely characterizing the dielectric properties of high temperature ceramic materials at high temperatures is presented for microwave frequencies. This technique is based on a high-quality (Q)-factor dielectrically-loaded cavity resonator, which allows for accurate characterization of both dielectric constant and loss tangent of the material. The dielectric properties of Silicon Carbonitride (SiCN) and Silicoboron Carbonitride (SiBCN) ceramics, developed at UCF Advanced Materials Processing and Analysis Center (AMPC) are characterized from 25 to 1300oC. It is observed that the dielectric constant and loss tangent of SiCN and SiBCN materials increase monotonously with temperature. This temperature dependency provides the valuable basis for development of wireless passive temperature sensors for high-temperature applications. Second, wireless temperature sensors are designed based on the aforementioned high-temperature ceramic materials. The dielectric constant of high-temperature ceramics increases monotonically with temperature and as a result changes the resonant frequency of the resonator. Therefore, the temperature can be extracted by measuring the change of the resonant frequency of the resonator. In order for the resonator to operate wirelessly, antennas need to be included in the design. Three different types of sensors, corresponding to different antenna configurations, are designed and the prototypes are fabricated and tested. All of the sensors successfully perform at temperatures over 1000oC. These wireless passive sensor designs will significantly benefit turbine engines in need of sensors operating at harsh environments.
Show less
Date Issued: 2012
Identifier: CFE0004791, ucf:49727
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004791

Title: Method for Real-Time Signal Selection for Passive Coherent Location Systems.
Creator: Johnson, Nicholas, Jones, W Linwood, Gong, Xun, Mikhael, Wasfy, Rockway, John, Lichtenberg, Christopher, University of Central Florida
Abstract / Description: Passive coherent location (PCL) systems use signals of opportunity to perform traditional radar detection, targeting, and tracking functions. Traditionally these signals include FM radio, digital TV, GSM, and GPS because of their availability in most urban environments. A benefit of having an abundance of signals is the ability to choose which of those best meet the desired system intentions. For example, one may want to choose a digital TV signal over an FM radio signal due to its range...
Show morePassive coherent location (PCL) systems use signals of opportunity to perform traditional radar detection, targeting, and tracking functions. Traditionally these signals include FM radio, digital TV, GSM, and GPS because of their availability in most urban environments. A benefit of having an abundance of signals is the ability to choose which of those best meet the desired system intentions. For example, one may want to choose a digital TV signal over an FM radio signal due to its range resolution characteristics. This work presents a novel algorithm for characterizing commercial signals for use in a PCL system. By analyzing each signal's ambiguity function in terms of amplitude, transmitter geometry, range and Doppler resolution, and sidelobe levels, a comparative evaluation can be made to decide which signals are best suited for an intended radar function. In addition, this research shows that multiple signals can be combined in the detection process to increase the probability of detection over that of a single signal. Finally, this research investigates the geometric considerations for PCL systems in terms of bistatic radar geometry. The results show zones of linear and non-linear relationships between time delay, range, and Doppler frequency.
Show less
Date Issued: 2017
Identifier: CFE0007123, ucf:51964
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007123

Title: Customizable Antenna Array Using Reconfigurable Antenna Elements.
Creator: Shirazi, Mahmoud, Gong, Xun, Wahid, Parveen, Jones, W Linwood, Abdolvand, Reza, Kuebler, Stephen, University of Central Florida
Abstract / Description: A shared-aperture reconfigurable slot-ring antenna array switching between different frequency bands and polarizations is presented for phased array applications. PIN diode switches are incorporated into the slots of the antenna to change the state of the reconfigurable slot-ring antenna array. Each frequency band has its own feeding lines which allows for the use of high-performance narrow-band transmit/receive (T/R) modules instead of ultra wideband (UWB) T/R modules. Furthermore, the...
Show moreA shared-aperture reconfigurable slot-ring antenna array switching between different frequency bands and polarizations is presented for phased array applications. PIN diode switches are incorporated into the slots of the antenna to change the state of the reconfigurable slot-ring antenna array. Each frequency band has its own feeding lines which allows for the use of high-performance narrow-band transmit/receive (T/R) modules instead of ultra wideband (UWB) T/R modules. Furthermore, the spacing between the elements in each frequency band is less than half free-space wavelength (?0) over the frequency band of operation which enables grating-lobe-free beam scanning. This is the first shared-aperture reconfigurable dual-polarized antenna with separate feeding for each band which is scalable to a larger array with element spacing of less than 0.5?0 in all frequency bands of operation.First, a switchable-band reconfigurable antenna array switching between L and C bands is presented. This antenna operates at 1.76/5.71 GHz with a fractional bandwidth (FBW) of 8.6%/11.5%, realized gain of 0.1/4.2 dBi and radiation efficiency of 66.6%/80.7% in the L-/C- band operating states, respectively. Second, a wideband version of the reconfigurable antenna element using fractal geometries is presented. This dual-polarized antenna element is switching between S and C bands with wide bandwidth in each operating state. In the S-/C-band operating state, this antenna shows 69.1%/58.3% FBW with a maximum realized gain of 2.4/3.1 dBi. Third, the wideband antenna element is extended to an antenna array. The reconfigurable dual-polarized antenna array with vertical coaxial feeding switches between S- and C-band states with full-band coverage. A 2(&)#215;2 S-band antenna array can be reconfigured to a 4(&)#215;4 C-band antenna array by activating/deactivating PIN diode switches. This antenna array shows 64.3%/66.7% FBW with 8.4/14.3 dBi maximum realized gain in the S-/C-band operating states, respectively. Finally, a reconfigurable antenna element covering three adjacent frequency bands is presented. The FBW of this tri-band antenna element is 75%/63%/26% in the S/C/X band state.
Show less
Date Issued: 2018
Identifier: CFE0007373, ucf:52092
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007373

Title: Hurricane Imaging Radiometer (HIRAD) tropical rainfall retrievals.
Creator: Alasgah, Abdusalam, Jones, W Linwood, Wahid, Parveen, Mikhael, Wasfy, Gong, Xun, Zec, Josko, University of Central Florida
Abstract / Description: The Hurricane Imaging Radiometer (HIRAD) is an airborne passive microwave remote sensor, developed to measure wind speed and rain rate in hurricanes. This dissertation concerns the development of a signal processing algorithm to infer tropical rainfall from HIRAD radiance (brightness temperature, Tb) measurements.The basis of the rain rate retrieval algorithm is an improved forward microwave radiative transfer model (RTM) that incorporates the HIRAD multi-antenna-beam geometry, and uses semi...
Show moreThe Hurricane Imaging Radiometer (HIRAD) is an airborne passive microwave remote sensor, developed to measure wind speed and rain rate in hurricanes. This dissertation concerns the development of a signal processing algorithm to infer tropical rainfall from HIRAD radiance (brightness temperature, Tb) measurements.The basis of the rain rate retrieval algorithm is an improved forward microwave radiative transfer model (RTM) that incorporates the HIRAD multi-antenna-beam geometry, and uses semi-empirical coefficients derived from an airborne experiment that occurred in the Gulf of Mexico off Tampa Bay in 2013. During this flight, HIRAD observed a squall line of thunderstorms simultaneously with an airborne meteorological radar (High Altitude Wind and Rain Profiler, HIWRAP), located on the same airplane. Also, ground based NEXRAD radars from the National Weather Service (located at Tampa and Tallahassee) provided high resolution simultaneous rain rate measurements.Using NEXRAD rainfall as the surface truth input to the HIRAD RTM, empirical rain microwave absorption coefficients were tuned to match the measured brightness temperatures. Also, the collocated HIWRAP radar reflectivity (dBZ) measurements were cross correlated with NEXRAD to derive the empirical HIWRAP radar reflectivity to rain rate relationship. Finally, the HIRAD measured Tbs were input to the HIRAD rain retrieval algorithm to derive estimates of rain rate, which were validated using the independent HIWRAP measurements of rain rate.
Show less
Date Issued: 2019
Identifier: CFE0007775, ucf:52379
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007775

Title: Reconfigurable Reflectarray Antennas with Bandwidth Enhancement for High Gain, Beam-Steering Applications.
Creator: Trampler, Michael, Gong, Xun, Wahid, Parveen, Jones, W Linwood, Chen, Kenle, Kuebler, Stephen, University of Central Florida
Abstract / Description: Reconfigurable reflectarrays are a class of antennas that combine the advantages of traditional parabolic antennas and phased array antennas. Chapter 1 discusses the basic operational theory of reflectarrays and their design. A review of previous research and the current status is also presented. Furthermore the inherent advantages and disadvantages of the reflectarray topography are presented. In chapter 2, a BST-integrated reflectarray operating at Ka band is presented. Due to the...
Show moreReconfigurable reflectarrays are a class of antennas that combine the advantages of traditional parabolic antennas and phased array antennas. Chapter 1 discusses the basic operational theory of reflectarrays and their design. A review of previous research and the current status is also presented. Furthermore the inherent advantages and disadvantages of the reflectarray topography are presented. In chapter 2, a BST-integrated reflectarray operating at Ka band is presented. Due to the monolithic integration of the tuning element, this design is then extended to V band where a novel interdigital gap configuration is utilized. Finally to overcome loss and phase limitations of the single resonant design, a BST-integrated, dual-resonance unit cell operating at Ka band is designed. While the losses are still high, a 360(&)deg; phase range is demonstrated.In chapter 3, the operational theory of dual-resonant array elements is introduced utilizing Q theory. An equivalent circuit is developed and used to demonstrate design tradeoffs. Using this theory the design procedure of a varactor tuned dual-resonant unit cell operating at X-band is presented. Detailed analysis of the design is performed by full-wave simulations and verified via measurements. In chapter 4, the array performance of the dual-resonance unit cell is analyzed. The effects of varying angles of incidence on the array element are studied using Floquet simulations. The beam scanning, cross-polarization and bandwidth performance of a 7(&)#215;7 element reflectarray is analyzed using full-wave simulations and verified via measurements.In chapter 5 a loss analysis of the dual-resonant reflectarray element is performed. Major sources of loss are identified utilizing full-wave simulations before an equivalent circuit is utilized to optimize the loss performance while maintaining a full phase range and improved bandwidth performance. Finally the dual-resonance unit cell is modified to support two linear polarizations. Overall, the operational and design theory of dual resonant reflectarray unit cells using Q theory is developed. A valuable equivalent circuit is developed and used to aid in array element design as well as optimize the loss and bandwidth performance. The proposed theoretical models provide valuable physical insight through the use of Q theory to greatly aid in reflectarray design
Show less
Date Issued: 2019
Identifier: CFE0007735, ucf:52457
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007735

Title: Frequency-Reconfigurable Microstrip Patch and Cavity-Backed Slot ESPARs.
Creator: Ouyang, Wei, Gong, Xun, Vosoughi, Azadeh, Wahid, Parveen, Abdolvand, Reza, Kuebler, Stephen, University of Central Florida
Abstract / Description: Wireless communication systems have rapidly evolved over the past decade which has led to an explosion of mobile data traffic. Since more and more wireless devices and sensors are being connected, the transition from the current 4G/LTE mobile network to 5G is expected to happen within the next decade. In order to improve signal-to-noise ratio (SNR), system capacity, and link budget, beam steerable antenna arrays are desirable due to their advantage in spatial selectivity and high directivity....
Show moreWireless communication systems have rapidly evolved over the past decade which has led to an explosion of mobile data traffic. Since more and more wireless devices and sensors are being connected, the transition from the current 4G/LTE mobile network to 5G is expected to happen within the next decade. In order to improve signal-to-noise ratio (SNR), system capacity, and link budget, beam steerable antenna arrays are desirable due to their advantage in spatial selectivity and high directivity. Electronically steerable parasitic array radiator (ESPAR) that can achieve low-cost continuously beamsteering using varactor diodes have attracted a lot of attention. This dissertation explores bandwidth enhancement of the ESPAR using frequency-reconfigurable microstrip patch and cavity-backed slot (CBS) antennas. In chapter 2, an ESPAR of three closely-coupled rectangular patch elements that do not use phase shifters is presented; the beamsteering is realized by tunable reactive loads which are used to control the mutual coupling between the elements. Additional loading varactors are strategically placed on the radiating edge of all the antenna elements to achieve a 15% continuous frequency tuning range while simultaneously preserving the beamsteering capability at each operating frequency. Therefore, this frequency-reconfigurable ESPAR is able to provide spectrum diversity in addition to the spatial diversity inherent in a frequency-fixed ESPAR. A prototype of the patch ESPAR is fabricated and demonstrated to operate from 0.87 to 1.02 GHz with an instantaneous fractional bandwidth (FBW) of ~1%. At each operating frequency, this ESPAR is able to scan from -20 to +20 degrees in the H plane. However, the beamsteering of the patch ESPAR is limited in the H-plane and its instantaneous S11 fractional bandwidth (FBW) is very narrow. This dissertation also explores how to achieve 2-D beamsteering with enhanced FBW using CBS antennas. A 20-element cavity-backed slot antenna array is designed and fabricated based on a CBS ESPAR cross subarray in chapter 5. This ESPAR array is able to steer the main beam from +45 degrees to -45 degrees in the E plane and from +40 degrees to -40 degrees in the H plane, respectively, without grating lobes in either plane. The impedance matching is maintained below -10 dB from 6.0 to 6.4 GHz (6.4% fractional bandwidth) at all scan angles. In addition, the CBS ESPAR exhibits minimum beam squint at all scan angles within the impedance matching bandwidth. This array successfully demonstrates the cost savings and associated reduction in the required number of phase shifters in the RF front end by employing ESPAR technology.
Show less
Date Issued: 2019
Identifier: CFE0007699, ucf:52426
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007699

Title: Design of Low-Capacitance Electrostatic Discharge (ESD) Protection Devices in Advanced Silicon Technologies.
Creator: Dong, Aihua, Sundaram, Kalpathy, Fan, Deliang, Gong, Xun, Wei, Lei, Salcedo, Javier, University of Central Florida
Abstract / Description: Electrostatic discharge (ESD) related failure is a major IC reliability concern and this is particularly true as technology continues shrink to nano-metric dimensions. ESD design window research shows that ESD robustness of victim devices keep decreasing from 350nm bulk technology to 7nm FinFET technologies. In the meantime, parasitic capacitance of ESD diode with same It2 in FinFET technologies is approximately 3X compared with that in planar technologies. Thus transition from planar to...
Show moreElectrostatic discharge (ESD) related failure is a major IC reliability concern and this is particularly true as technology continues shrink to nano-metric dimensions. ESD design window research shows that ESD robustness of victim devices keep decreasing from 350nm bulk technology to 7nm FinFET technologies. In the meantime, parasitic capacitance of ESD diode with same It2 in FinFET technologies is approximately 3X compared with that in planar technologies. Thus transition from planar to FinFET technology requires more robust ESD protection however the large parasitic capacitance of ESD protection cell is problematic in high-speed interface design. To reduce the parasitic capacitance, a dual diode silicon controlled rectifier (DD-SCR) is presented in this dissertation. This design can exhibit good trade-offs between ESD robustness and parasitic capacitance characteristics. Besides, different bounding materials lead to performance variations in DD-SCRs are compared. Radio frequency (RF) technology is also demanded low capacitance ESD protection. To address this concern, a ?-network is presented, providing robust ESD protection for 10-60 GHz RF circuit. Like a low pass ? filter, the network can reflect high frequency RF signals and transmit low frequency ESD pulses. Given proper inductor value, networks can work as robust ESD solutions at a certain Giga Hertz frequency range, making this design suitable for broad band protection in RF input/outputs (I/Os). To increase the holding voltage and reduce snapback, a resistor assist triggering heterogeneous stacking structure is presented in this dissertation, which can increase the holding voltage and also keep the trigger voltage nearly as same as a single SCR device.
Show less
Date Issued: 2018
Identifier: CFE0007172, ucf:52251
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007172

Title: Semiconductor Device Modeling, Simulation, and Failure Prediction for Electrostatic Discharge Conditions.
Creator: Li, Hang, Sundaram, Kalpathy, Batarseh, Issa, Fan, Deliang, Gong, Xun, Salcedo, Javier, University of Central Florida
Abstract / Description: Electrostatic Discharge (ESD) caused failures are major reliability issues in IC industry. Device modeling for ESD conditions is necessary to evaluate ESD robustness in simulation. Although SPICE model is accurate and efficient for circuit simulations in most cases, devices under ESD conditions operate in abnormal status. SPICE model cannot cover the device operating region beyond normal operation.Thermal failure is one of the main reasons to cause device failure under ESD conditions. A...
Show moreElectrostatic Discharge (ESD) caused failures are major reliability issues in IC industry. Device modeling for ESD conditions is necessary to evaluate ESD robustness in simulation. Although SPICE model is accurate and efficient for circuit simulations in most cases, devices under ESD conditions operate in abnormal status. SPICE model cannot cover the device operating region beyond normal operation.Thermal failure is one of the main reasons to cause device failure under ESD conditions. A compact model is developed to predict thermal failure with circuit simulators. Instead of considering the detailed failure mechanisms, a failure temperature is introduced to indicate device failure. The developed model is implemented by a multiple-stage thermal network.P-N junction is the fundamental structure for ESD protection devices. An enhanced diode model is proposed and is used to simulate the device behaviors for ESD events. The model includes all physical effects for ESD conditions, which are voltage overshoot, self-heating effect, velocity saturation and thermal failure. The proposed model not only can fit the I-V and transient characteristics, but also can predict failure for different pulses.Safe Operating Area (SOA) is an important factor to evaluate the LDMOS performance. The transient SOA boundary is considered as power-defined. By placing the failure monitor under certain conditions, the developed modeling methodology can predict the boundary of transient SOA for any short pulse stress conditions. No matter failure happens before or after snapback phenomenon.Weibull distribution is popular to evaluate the dielectric lifetime for CVS. By using the transformative version of power law, the pulsing stresses are converted into CVS, and TDDB under ESD conditions for SiN MIMCAPs is analyzed. The thickness dependency and area independency of capacitor breakdown voltage is observed, which can be explained by the constant ?E model instead of conventional percolation model.
Show less
Date Issued: 2019
Identifier: CFE0007670, ucf:52512
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007670

Title: Design and Implementation of Silicon-Based MEMS Resonators for Application in Ultra Stable High Frequency Oscillators.
Creator: Shahraini, Sarah, Abdolvand, Reza, Gong, Xun, Sundaram, Kalpathy, Kapoor, Vikram, Rajaraman, Swaminathan, University of Central Florida
Abstract / Description: The focus of this work is to design and implement resonators for ultra-stable high-frequency ((>)100MHz) silicon-based MEMS oscillators. Specifically, two novel types of resonators are introduced that push the performance of silicon-based MEMS resonators to new limits. Thin film Piezoelectric-on-Silicon (TPoS) resonators have been shown to be suitable for oscillator applications due to their combined high quality factor, coupling efficiency, power handling and doping-dependent temperature...
Show moreThe focus of this work is to design and implement resonators for ultra-stable high-frequency ((>)100MHz) silicon-based MEMS oscillators. Specifically, two novel types of resonators are introduced that push the performance of silicon-based MEMS resonators to new limits. Thin film Piezoelectric-on-Silicon (TPoS) resonators have been shown to be suitable for oscillator applications due to their combined high quality factor, coupling efficiency, power handling and doping-dependent temperature-frequency behavior. This thesis is an attempt to utilize the TPoS platform and optimize it for extremely stable high-frequency oscillator applications.To achieve the said objective, two main research venues are explored. Firstly, quality factor is systematically studied and anisotropy of single crystalline silicon (SCS) is exploited to enable high-quality factor side-supported radial-mode (aka breathing mode) TPoS disc resonators through minimization of anchor-loss. It is then experimentally demonstrated that in TPoS disc resonators with tethers aligned to [100], unloaded quality factor improves from ~450 for the second harmonic mode at 43 MHz to ~11,500 for the eighth harmonic mode at 196 MHz. Secondly, thickness quasi-Lam(&)#233; modes are studied and demonstrated in TPoS resonators for the first time. It is shown that thickness quasi-Lam(&)#233; modes (TQLM) could be efficiently excited in silicon with very high quality factor (Q). A quality factor of 23.2 k is measured in vacuum at 185 MHz for a fundamental TQLM-TPoS resonators designed within a circular acoustic isolation frame. Quality factor of 12.6 k and 6 k are also measured for the second- and third- harmonic TQLM TPoS resonators at 366 MHz and 555 MHz respectively. Turn-over temperatures between 40 (&)deg;C to 125 (&)deg;C are also designed and measured for TQLM TPoS resonators fabricated on degenerately N-doped silicon substrates. The reported extremely high quality factor, very low motional resistance, and tunable turn-over temperatures (>)80 (&)#186;C make these resonators a great candidate for ultra-stable oven-controlled high-frequency MEMS oscillators.
Show less
Date Issued: 2019
Identifier: CFE0007861, ucf:52775
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007861

Title: X-ray Radiation Enabled Cancer Detection and Treatment with Nanoparticles.
Creator: Hossain, Mainul, Su, Ming, Behal, Aman, Gong, Xun, Hu, Haiyan, Kapoor, Vikram, Deng, Weiwei, University of Central Florida
Abstract / Description: Despite significant improvements in medical sciences over the last decade, cancer still continues to be a major cause of death in humans throughout the world. Parallel to the efforts of understanding the intricacies of cancer biology, researchers are continuously striving to develop effective cancer detection and treatment strategies. Use of nanotechnology in the modern era opens up a wide range of possibilities for diagnostics, therapies and preventive measures for cancer management....
Show moreDespite significant improvements in medical sciences over the last decade, cancer still continues to be a major cause of death in humans throughout the world. Parallel to the efforts of understanding the intricacies of cancer biology, researchers are continuously striving to develop effective cancer detection and treatment strategies. Use of nanotechnology in the modern era opens up a wide range of possibilities for diagnostics, therapies and preventive measures for cancer management. Although, existing strategies of cancer detection and treatment, using nanoparticles, have been proven successful in case of cancer imaging and targeted drug deliveries, they are often limited by poor sensitivity, lack of specificity, complex sample preparation efforts and inherent toxicities associated with the nanoparticles, especially in case of in-vivo applications. Moreover, the detection of cancer is not necessarily integrated with treatment. X-rays have long been used in radiation therapy to kill cancer cells and also for imaging tumors inside the body using nanoparticles as contrast agents. However, X-rays, in combination with nanoparticles, can also be used for cancer diagnosis by detecting cancer biomarkers and circulating tumor cells. Moreover, the use of nanoparticles can also enhance the efficacy of X-ray radiation therapy for cancer treatment.This dissertation describes a novel in vitro technique for cancer detection and treatment using X-ray radiation and nanoparticles. Surfaces of synthesized metallic nanoparticles have been modified with appropriate ligands to specifically target cancer cells and biomarkers in vitro. Characteristic X-ray fluorescence signals from the X-ray irradiated nanoparticles are then used for detecting the presence of cancer. The method enables simultaneous detection of multiple cancer biomarkers allowing accurate diagnosis and early detection of cancer. Circulating tumor cells, which are the primary indicators of cancer metastasis, have also been detected where the use of magnetic nanoparticles allows enrichment of rare cancer cells prior to detection. The approach is unique in that it integrates cancer detection and treatment under one platform, since, X-rays have been shown to effectively kill cancer cells through radiation induced DNA damage. Due to high penetrating power of X-rays, the method has potential applications for in vivo detection and treatment of deeply buried cancers in humans. The effect of nanoparticle toxicity on multiple cell types has been investigated using conventional cytotoxicity assays for both unmodified nanoparticles as well as nanoparticles modified with a variety of surface coatings. Appropriate surface modifications have significantly reduced inherent toxicity of nanoparticles, providing possibilities for future clinical applications. To investigate cellular damages caused by X-ray radiation, an on-chip biodosimeter has been fabricated based on three dimensional microtissues which allows direct monitoring of responses to X-ray exposure for multiple mammalian cell types. Damage to tumor cells caused by X-rays is known to be significantly higher in presence of nanoparticles which act as radiosensitizers and enhance localized radiation doses. An analytical approach is used to investigate the various parameters that affect the radiosensitizing properties of the nanoparticles. The results can be used to increase the efficacy of nanoparticle aided X-ray radiation therapy for cancer treatment by appropriate choice of X-ray beam energy, nanoparticle size, material composition and location of nanoparticle with respect to the tumor cell nucleus.
Show less
Date Issued: 2012
Identifier: CFE0004547, ucf:49242
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004547

Title: Surface Acoustic Wave (SAW) Cryogenic Liquid and Hydrogen Gas Sensors.
Creator: Fisher, Brian, Malocha, Donald, Gong, Xun, Likamwa, Patrick, Richie, Samuel, Youngquist, Robert, University of Central Florida
Abstract / Description: This research was born from NASA Kennedy Space Center's (KSC) need for passive, wireless and individually distinguishable cryogenic liquid and H2 gas sensors in various facilities. The risks of catastrophic accidents, associated with the storage and use of cryogenic fluids may be minimized by constant monitoring. Accidents involving the release of H2 gas or LH2 were responsible for 81% of total accidents in the aerospace industry. These problems may be mitigated by the implementation of a...
Show moreThis research was born from NASA Kennedy Space Center's (KSC) need for passive, wireless and individually distinguishable cryogenic liquid and H2 gas sensors in various facilities. The risks of catastrophic accidents, associated with the storage and use of cryogenic fluids may be minimized by constant monitoring. Accidents involving the release of H2 gas or LH2 were responsible for 81% of total accidents in the aerospace industry. These problems may be mitigated by the implementation of a passive (or low-power), wireless, gas detection system, which continuously monitors multiple nodes and reports temperature and H2 gas presence. Passive, wireless, cryogenic liquid level and hydrogen (H2) gas sensors were developed on a platform technology called Orthogonal Frequency Coded (OFC) surface acoustic wave (SAW) radio frequency identification (RFID) tag sensors. The OFC-SAW was shown to be mechanically resistant to failure due to thermal shock from repeated cycles between room to liquid nitrogen temperature. This suggests that these tags are ideal for integration into cryogenic Dewar environments for the purposes of cryogenic liquid level detection. Three OFC-SAW H2 gas sensors were simultaneously wirelessly interrogated while being exposed to various flow rates of H2 gas. Rapid H2 detection was achieved for flow rates as low as 1ccm of a 2% H2, 98% N2 mixture. A novel method and theory to extract the electrical and mechanical properties of a semiconducting and high conductivity thin-film using SAW amplitude and velocity dispersion measurements were also developed. The SAW device was shown to be a useful tool in analysis and characterization of ultrathin and thin films and physical phenomena such as gas adsorption and desorption mechanisms.?
Show less
Date Issued: 2012
Identifier: CFE0004536, ucf:49258
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004536

Title: Experimental study and modeling of mechanical micro-machining of particle reinforced heterogeneous materials.
Creator: Liu, Jian, Xu, Chengying, An, Linan, Gordon, Ali, Bai, Yuanli, Gong, Xun, University of Central Florida
Abstract / Description: This study focuses on developing explicit analytical and numerical process models for mechanical micro-machining of heterogeneous materials. These models are used to select suitable process parameters for preparing and micro-machining of these advanced materials. The material system studied in this research is Magnesium Metal Matrix Composites (Mg-MMCs) reinforced with nano-sized and micro-sized silicon carbide (SiC) particles.This research is motivated by increasing demands of miniaturized...
Show moreThis study focuses on developing explicit analytical and numerical process models for mechanical micro-machining of heterogeneous materials. These models are used to select suitable process parameters for preparing and micro-machining of these advanced materials. The material system studied in this research is Magnesium Metal Matrix Composites (Mg-MMCs) reinforced with nano-sized and micro-sized silicon carbide (SiC) particles.This research is motivated by increasing demands of miniaturized components with high mechanical performance in various industries. Mg-MMCs become one of the best candidates due to its light weight, high strength, and high creep/wear resistance. However, the improved strength and abrasive nature of the reinforcements bring great challenges for the subsequent micro-machining process.Systematic experimental investigations on the machinability of Mg-MMCs reinforced with SiC nano-particles have been conducted. The nanocomposites containing 5 Vol.%, 10 Vol.% and 15 Vol.% reinforcements, as well as pure magnesium, are studied by using the Design of Experiment (DOE) method. Cutting forces, surface morphology and surface roughness are characterized to understand the machinability of the four materials. Based on response surface methodology (RSM) design, experimental models and related contour plots have been developed to build a connection between different materials properties and cutting parameters. Those models can be used to predict the cutting force, the surface roughness, and then optimize the machining process.An analytical cutting force model has been developed to predict cutting forces of Mg-MMCs reinforced with nano-sized SiC particles in the micro-milling process. This model is different from previous ones by encompassing the behaviors of reinforcement nanoparticles in three cutting scenarios, i.e., shearing, ploughing and elastic recovery. By using the enhanced yield strength in the cutting force model, three major strengthening factors are incorporated, including load-bearing effect, enhanced dislocation density strengthening effect and Orowan strengthening effect. In this way, the particle size and volume fraction, as significant factors affecting the cutting forces, are explicitly considered. In order to validate the model, various cutting conditions using different size end mills (100 (&)#181;m and 1 mm dia.) have been conducted on Mg-MMCs with volume fraction from 0 (pure magnesium) to 15 Vol.%. The simulated cutting forces show a good agreement with the experimental data. The proposed model can predict the major force amplitude variations and force profile changes as functions of the nanoparticles' volume fraction. Next, a systematic evaluation of six ductile fracture models has been conducted to identify the most suitable fracture criterion for micro-scale cutting simulations. The evaluated fracture models include constant fracture strain, Johnson-Cook, Johnson-Cook coupling criterion, Wilkins, modified Cockcroft-Latham, and Bao-Wierzbicki fracture criterion. By means of a user material subroutine (VUMAT), these fracture models are implemented into a Finite Element (FE) orthogonal cutting model in ABAQUS/Explicit platform. The local parameters (stress, strain, fracture factor, velocity fields) and global variables (chip morphology, cutting forces, temperature, shear angle, and machined surface integrity) are evaluated. Results indicate that by coupling with the damage evolution, the capability of Johnson-Cook and Bao-Wierzbicki can be further extended to predict accurate chip morphology. Bao-Wierzbiki-based coupling model provides the best simulation results in this study. The micro-cutting performance of MMCs materials has also been studied by using FE modeling method. A 2-D FE micro-cutting model has been constructed. Firstly, homogenized material properties are employed to evaluate the effect of particles' volume fraction. Secondly, micro-structures of the two-phase material are modeled in FE cutting models. The effects of the existing micro-sized and nano-sized ceramic particles on micro-cutting performance are carefully evaluated in two case studies. Results show that by using the homogenized material properties based on Johnson-Cook plasticity and fracture model with damage evolution, the micro-cutting performance of nano-reinforced Mg-MMCs can be predicted. Crack generation for SiC particle reinforced MMCs is different from their homogeneous counterparts; the effect of micro-sized particles is different from the one of nano-sized particles.In summary, through this research, a better understanding of the unique cutting mechanism for particle reinforced heterogeneous materials has been obtained. The effect of reinforcements on micro-cutting performance is obtained, which will help material engineers tailor suitable material properties for special mechanical design, associated manufacturing method and application needs. Moreover, the proposed analytical and numerical models provide a guideline to optimize process parameters for preparing and micro-machining of heterogeneous MMCs materials. This will eventually facilitate the automation of MMCs' machining process and realize high-efficiency, high-quality, and low-cost manufacturing of composite materials.
Show less
Date Issued: 2012
Identifier: CFE0004570, ucf:49196
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004570

ESD (3)	+ -
Antennas (2)	+ -
BST (2)	+ -
Beam steering (2)	+ -
Filter (2)	+ -

Passive (2)	+ -
RF (2)	+ -
Reconfigurable antennas (2)	+ -
Resonator (2)	+ -
high speed (2)	+ -
wireless sensors (2)	+ -
28nm CMOS (1)	+ -
Antenna (1)	+ -
Array (1)	+ -
Arrays (1)	+ -
Barium Strontium Titanate (1)	+ -
CMOS (1)	+ -
Cavity resonator (1)	+ -
Coupling conditions (1)	+ -
DRO (1)	+ -
Diamond (1)	+ -
Dielectric Resonator (1)	+ -
Direction Finding (1)	+ -
ESD simulation (1)	+ -
Electrostatic discharge (1)	+ -
Embedded Oscillator (1)	+ -
FPGA Control System (1)	+ -
Filters (1)	+ -
GaN (1)	+ -
Grating waveguides (1)	+ -

Gong, Xun (36)	+ -
University of Central Florida (36)	+ -
Wahid, Parveen (13)	+ -
Sundaram, Kalpathy (9)	+ -
Yuan, Jiann-Shiun (6)	+ -

Abdolvand, Reza (5)	+ -
Jones, W Linwood (5)	+ -
Malocha, Donald (5)	+ -
An, Linan (4)	+ -
Jones, W (4)	+ -
Kuebler, Stephen (4)	+ -
Salcedo, Javier (4)	+ -
Wu, Xinzhang (4)	+ -
Fathpour, Sasan (3)	+ -
Jin, Yier (3)	+ -
Kapoor, Vikram (3)	+ -
Richie, Samuel (3)	+ -
Cho, Hyoung Jin (2)	+ -
Fan, Deliang (2)	+ -
Likamwa, Patrick (2)	+ -
Liou, Juin (2)	+ -
Mikhael, Wasfy (2)	+ -
Wu, Thomas (2)	+ -
Xu, Chengying (2)	+ -
Abouraddy, Ayman (1)	+ -
Alasgah, Abdusalam (1)	+ -
Bai, Yuanli (1)	+ -
Banaei, Seyed Esmaeil (1)	+ -
Batarseh, Issa (1)	+ -
Behal, Aman (1)	+ -

Search In

Pages

Pages

Sort Results By:

Narrow results by:

Topical Subject

Collection

Type of Resource

Language

Creator

Format

Owner