View All Items

Title: Heat Transfer and Friction Augmentation in a Narrow Rectangular Duct with Symmetrical and Non-Symmetrical Wedge-Shaped Turbulators.
Creator: Valentino, Michelle, Kapat, Jayanta, Deng, Weiwei, Kassab, Alain, University of Central Florida
Abstract / Description: The need for cleaner and more fuel efficient means to produce electricity is growing steadily. Advancements in cooling technologies contribute to the improvements in turbine efficiency and are used for gas turbines and for power generation in automotive, aviation, as well as in naval applications, and many more. Studies introducing turbulators on walls of internal cooling channels, which can be applied to hot gas components and in recuperative heat exchangers, have been reviewed for their...
Show moreThe need for cleaner and more fuel efficient means to produce electricity is growing steadily. Advancements in cooling technologies contribute to the improvements in turbine efficiency and are used for gas turbines and for power generation in automotive, aviation, as well as in naval applications, and many more. Studies introducing turbulators on walls of internal cooling channels, which can be applied to hot gas components and in recuperative heat exchangers, have been reviewed for their ability to promote heat transfer in the channel while observing pressure loss caused by adding the features. Several types of turbulators have been studied; ribs, pin fins, dimples, wedges, and scales are some examples of features that have been added to walls of internal cooling channels or heat exchangers to increase heat transfer. This study focuses on two types of wedge turbulator designs, a full symmetrical wedge and a half, or non-symmetrical right-triangular wedge for the purpose of disrupting the thermal boundary layer close to hot walls without causing large-scale mixing and pressure drops. There are two sizes of the wedges, the first set of full and half wedges have an e/Dh=0.10 with the second at e/Dh=0.40, a feature that fills the height of the boundary layer. There are six cases studied, two one-wall and four two-wall cases in a 2:1 aspect ratio channel at Reynolds numbers of 10,000, 20,000, 30,000, and 40,000. Two experimental setups are utilized: a segmented copper block and transient TLC, along with numerical simulation for computational flow visualization. Wall temperature data is collected from all four walls for the copper experimental setup and three walls on the transient TLC setup. The fourth wall of the acrylic test section for the transient TLC tests is utilized for pressure testing, where static pressure ports are placed along the side wall. Although the small features did not show large influence in heat transfer on the side walls as much as the larger features or as high of heat transfer on the featured walls, the minimal pressure loss in the channel kept overall thermal performance of the small two wall full wedge features very high. The case of the large half wedge on two walls also showed very high thermal performance, having pressure loss values nearly half of the same sized (length and height) full wedge feature while having the ability to incorporate side walls into the overall heat transfer enhancement. The results found in the experimental setups are supported by the visualization of flow characteristics from the numerical testing. Comparing the initial wedge study to recent full rib studies show the wedges have similar improvements in heat transfer to the full rib cases with friction augmentations 5 to 10 times lower than the full rib cases. Further improvements to wedge heat transfer and pressure drop can be done by determining optimal wedge size and orientation.
Show less
Date Issued: 2011
Identifier: CFE0004489, ucf:49299
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004489

Title: A Full Coverage Film Cooling Study: The Effect of an Alternating Compound Angle.
Creator: Hodges, Justin, Kapat, Jayanta, Gordon, Ali, Vasu Sumathi, Subith, University of Central Florida
Abstract / Description: This thesis is an experimental and numerical full-coverage film cooling study. The objective of this work is the quantification of local heat transfer augmentation and adiabatic film cooling effectiveness for two full-coverage film cooling geometries. Experimental data was acquired with a scientific grade CCD camera, where images are taken over the heat transfer surface, which is painted with a temperature sensitive paint. The CFD component of this study served to evaluate how well the v2-f...
Show moreThis thesis is an experimental and numerical full-coverage film cooling study. The objective of this work is the quantification of local heat transfer augmentation and adiabatic film cooling effectiveness for two full-coverage film cooling geometries. Experimental data was acquired with a scientific grade CCD camera, where images are taken over the heat transfer surface, which is painted with a temperature sensitive paint. The CFD component of this study served to evaluate how well the v2-f turbulence model predicted film cooling effectiveness throughout the array, as compared with experimental data. The two staggered arrays tested are different from one another through a compound angle shift after 12 rows of holes. The compound angle shifts from ?=-45(&)deg; to ?=+45(&)deg; at row 13. Each geometry had 22 rows of cylindrical film cooling holes with identical axial and lateral spacing (X/D=P/D=23). Levels of laterally averaged film cooling effectiveness for the superior geometry approach 0.20, where the compound angle shift causes a decrease in film cooling effectiveness. Levels of heat transfer augmentation maintain values of nearly h/h0=1.2. There is no effect of compound angle shift on heat transfer augmentation observed. The CFD results are used to investigate the detrimental effect of the compound angle shift, while the SST k-? turbulence model shows to provide the best agreement with experimental results.
Show less
Date Issued: 2015
Identifier: CFE0005626, ucf:50228
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0005626

Title: STUDY OF HEAT TRANSFER CHARACTERISTICS OF IMPINGING AIR JET USING PRESSURE ANDN TEMPERATURE SENSITIVE LUMINESCENT PAINT.
Creator: Liu, Quan, Kapat, Jayanta, University of Central Florida
Abstract / Description: Luminescent coating measurement system is a relatively new technology for quantitative pressure and temperature measurement. Usually referred to as Pressure Sensitive Paint (PSP) and Temperature Sensitive Paint (TSP), luminescent coatings contain sensor molecules, which undergoes a luminescent transition when excited with light of proper wavelength. The reaction is pressure and/or temperature sensitive. The image of TSP or PSP coated model surface can be captured with a scientific grade...
Show moreLuminescent coating measurement system is a relatively new technology for quantitative pressure and temperature measurement. Usually referred to as Pressure Sensitive Paint (PSP) and Temperature Sensitive Paint (TSP), luminescent coatings contain sensor molecules, which undergoes a luminescent transition when excited with light of proper wavelength. The reaction is pressure and/or temperature sensitive. The image of TSP or PSP coated model surface can be captured with a scientific grade camera and then processed to obtain full field temperature and pressure distribution with very high fidelity. The preparation time of the technique is short. The measurement system offers an economic alternative to conventional testing methods using large number of pressure taps and thermocouples. The purpose of the experiment in this thesis is to take the benefits of the TSP and PSP technique, develop a well-controlled process and then apply the technique for a fundamental study on jet impingement heat transfer. First, Uni-Coat TSP and Binary-FIB PSP purchased from ISSI Inc. are calibrated to high accuracy. The calibration uncertainty of TSP and PSP are found to be ±0.93 °C and ±0.12 psi over temperature and pressure ranges of 22 to 90 ° C and 5 to 14.7 psia, respectively. The photodegradation of TSP is then investigated with the same calibration system. The photodegradation refers to the phenomenon of decreasing emission intensity as the luminescent paint is exposed to the illumination light during testing. It was found that photodegradation rate is a strong function of temperature and the optical power of illumination lighting. The correlation developed in this work is expected to compensate the degradation of TSP to achieve high measurement accuracy. Both TSP and PSP were then applied in the flow and heat transfer measurement of single round impinging air jet. Various separation distance (Z/D) and jet Reynolds number are tested. Pressure measurement on the jet impinged target surface using PSP clearly shows the boundary of jet impingement zone, which broadens with separation distance. In heat transfer experiment using TSP, the "second peak" in local heat transfer occurring at radial distance r/D around 2 is clearly observed when the separation distance Z/D is shorter than the length of jet potential core. The slight variation in radial location and the amplitude of the "second peak" are captured as Z/D and jet Reynolds number change. The optimum Z/D of stagnation point heat transfer is found to be around 5. The effect of jet nozzle configuration is investigated. It is found that the heat transfer rate associated with "tube jet" is generally higher than that of "plate jet". The difference in heat transfer between the two jet configurations is related to the weaker entrainment effect associated with "plate jet", where the entrainment of surrounding air is confined by the injection plate, especially under small Z/D circumstances. When compared with the benchmark data in the literature, the averaged heat transfer data of "tube jet" matches the empirical data better than those of "plate jet". The maximum difference is 3.3% for tube jet versus 15.4% for plate jet at Reynolds number of 60000 and Z/D of 5. The effect of surface roughness on jet impingement heat transfer is also studied. Heat transfer can be significantly increased by the enhanced roughness of the target surface. The largest roughness effect is achieved near stagnation point at high jet Reynolds number. Compared to the heat transfer to a smooth plate, as high as 30.9% increase in area-averaged Nusselt number is observed over a rough surface at r/D=1.5 and jet Reynolds number of 60000. The most significant advance of the present work is that both temperature and pressure measurement be obtained with the same measurement system and with accuracy comparable to traditional testing methods. The procedures that were employed in this work should be easy to apply in any university or industrial testing facility. It provides a rapid testing tool that can help solve complex problems in aerodynamics and heat transfer
Show less
Date Issued: 2006
Identifier: CFE0000960, ucf:46747
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0000960

Title: Heat Transfer and Pressure Measurements from Jet Array Impingement onto a Large Radius Curved Surface.
Creator: Harrington, John, Kapat, Jayanta, Ahmed, Kareem, Vasu Sumathi, Subith, University of Central Florida
Abstract / Description: This study investigates the heat transfer and pressure drop characteristics of jet array impingement in two distinct parts. In the first part, the performance of a uniform array of jets on both a flat and a large radius curved target surface are compared. This comparison was done at average jet Reynolds number ranging from 55,000 to 125,000. In the second part, the characteristics of a non-uniform array of jets, more typical of geometries used in actual gas turbine combustors, are...
Show moreThis study investigates the heat transfer and pressure drop characteristics of jet array impingement in two distinct parts. In the first part, the performance of a uniform array of jets on both a flat and a large radius curved target surface are compared. This comparison was done at average jet Reynolds number ranging from 55,000 to 125,000. In the second part, the characteristics of a non-uniform array of jets, more typical of geometries used in actual gas turbine combustors, are investigated, including the effects of the removal of downstream rows and the placement of rib features onto the target surface. The non-uniform configurations studied have varying hole diameters and geometric spacing for spatial tuning of the heat transfer behavior. First row jet Reynolds numbers ranging from 50,000 to 160,000 are reported. For all configurations, spent air is drawn out in a single direction which is tangential to the target plate curvature. A steady-state measurement technique utilizing temperature sensitive paint (TSP) was used on the target surface to obtain heat transfer coefficients, while pressure taps placed on the sidewall and jet plate were used to evaluate the pressure and flow distribution in the impingement channel. Alongside the experimental work, CFD simulations were performed utilizing the v^2-f eddy viscosity turbulence model. The results from the uniform array impingement onto a curved surface comparison show that the large radius curvature of the current geometry has little to no effect on the flow distribution and heat transfer of the array.The non-uniform array results illustrate the applicability of tuning a jet impingement array using varying jet diameters and spacing. However, there are some difficulties in obtaining streamwise pitch resolved heat transfer predictions for non-uniform arrays as current open literature correlations for uniform arrays are shown to be not applicable. The computational results from this study show that simulations can be used to obtain initial predictions, with streamwise pitch averaged Nu values found to be within 20% of experimental results. The use of ribs downstream in place of several jet rows was shown to yield similar heat transfer results at lower pressure drop levels.
Show less
Date Issued: 2016
Identifier: CFE0006317, ucf:51547
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0006317

Title: COMPARISON OF SQUARE-HOLE AND ROUND-HOLE FILM COOLING: A COMPUTATIONAL STUDY.
Creator: Durham, Michael Glenn, Kapat, Jay, University of Central Florida
Abstract / Description: Film cooling is a method used to protect surfaces exposed to high-temperature flows such as those that exist in gas turbines. It involves the injection of secondary fluid (at a lower temperature than that of the main flow) that covers the surface to be protected. This injection is through holes that can have various shapes; simple shapes such as those with a straight circular (by drilling) or straight square (by EDM) cross-section are relatively easy and inexpensive to create. Immediately...
Show moreFilm cooling is a method used to protect surfaces exposed to high-temperature flows such as those that exist in gas turbines. It involves the injection of secondary fluid (at a lower temperature than that of the main flow) that covers the surface to be protected. This injection is through holes that can have various shapes; simple shapes such as those with a straight circular (by drilling) or straight square (by EDM) cross-section are relatively easy and inexpensive to create. Immediately downstream of the exit of a film cooling hole, a so-called horseshoe vortex structure consisting of a pair of counter-rotating vortices is formed. This vortex formation has an effect on the distribution of film coolant over the surface being protected. The fluid dynamics of these vortices is dependent upon the shape of the film cooling holes, and therefore so is the film coolant coverage which determines the film cooling effectiveness distribution and also has an effect on the heat transfer coefficient distribution. Differences in horseshoe vortex structures and in resultant effectiveness distributions are shown for circular and square hole cases for blowing ratios of 0.33, 0.50, 0.67, 1.00, and 1.33. The film cooling effectiveness values obtained are compared with experimental and computational data of Yuen and Martinez-Botas (2003a) and Walters and Leylek (1997). It was found that in the main flow portion of the domain immediately downstream of the cooling hole exit, there is greater lateral separation between the vortices in the horseshoe vortex pair for the case of the square hole. This was found to result in the square hole providing greater centerline film cooling effectiveness immediately downstream of the hole and better lateral film coolant coverage far downstream of the hole.
Show less
Date Issued: 2004
Identifier: CFE0000044, ucf:46080
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0000044

Title: STUDY OF FILM COOLING EFFECTIVENESS: CONICAL, TRENCHED AND ASYMMETRICAL SHAPED HOLES.
Creator: Zuniga, Humberto, Kapat, Jayanta, University of Central Florida
Abstract / Description: Film cooling is a technique whereby air from the compressor stage of a gas turbine engine is diverted for cooling purposes to parts, such as the turbine stage, that operate at very high temperatures. Cooling arrangements include impingement jets, finned, ribbed and turbulated channels, and rows of film cooling holes, all of which over the years have become progressively more complex. This costly, but necessary complexity is a result of the industry's push to run engines at increasingly higher...
Show moreFilm cooling is a technique whereby air from the compressor stage of a gas turbine engine is diverted for cooling purposes to parts, such as the turbine stage, that operate at very high temperatures. Cooling arrangements include impingement jets, finned, ribbed and turbulated channels, and rows of film cooling holes, all of which over the years have become progressively more complex. This costly, but necessary complexity is a result of the industry's push to run engines at increasingly higher turbine inlet temperatures. Higher temperatures mean higher efficiency, but they also mean that the turbine first stage operates hundreds of degrees Kelvin above the melting point of the metal core of the vanes and blades. Existing cooling technology and materials make it possible to protect these parts and allow them to function for extended periods of time--but this comes at a price: the compressed air that is used for cooling represents a considerable penalty in overall turbine efficiency. The aim of current cooling research is threefold: to improve the protection of components from extreme fluxes in order to extend the life of the parts; to increase the inlet turbine operating temperature; and to reduce the amount of air that is diverted from the compressor for cooling. Current film cooling schemes consist of forcing air through carefully machined holes on a part and ejecting it at an angle with the intent of cooling that part by blanketing the surface downstream of the point of ejection. The last major development in the field has been the use of expanded hole exits, which reduce coolant momentum and allow for greater surface coverage. Researchers and designers are continuously looking for novel geometries and arrangements that would increase the level of protection or maintain it while using less coolant. This dissertation investigates such novel methods which one day may include combinations of cylindrical and fan-shaped holes embedded inside trenches, conical holes, or even rows of asymmetric fan-shaped holes. The review of current literature reveals that very few investigations have been done on film cooling effectiveness for uniformly diffusing conical holes. They have been treated as a sort of side novelty since industrial partners often say they are hard to manufacture. To extend our understanding of effectiveness of conical holes, the present study investigates the effect of increasing diffusion angle, as well as the effect of adding a cylindrical entrance length to a conical hole. The measurements were made in the form of film cooling effectiveness and the technique used was temperature sensitive paint. Eight different conical geometries were tested in the form of coupons with rows of holes. The geometry of the holes changed from pure cylindrical holes, a 0° cylindrical baseline, to an 8° pure cone. The coupons were tested in a closed loop wind tunnel at blowing ratios varying from 0.5 to 1.5, and the coolant employed was nitrogen gas. Results indicate that the larger conical holes do, in fact offer appropriate protection and that the holes with the higher expansion angles perform similar to fan-shaped baseline holes, even at the higher blower ratios. The study was also extended to two other plates in which the conical hole was preceded by a cylindrical entry length. The performance of the conical holes improves as a result of the entry length and this is seen at the higher blowing ratios in the form of a delay in the onset of jet detachment. The results of this study show that conical expanding holes are a viable geometry and that their manufacturing can be made easier with a cylindrical entry length, at the same time improving the performance of these holes. Trench cooling consists of having film cooling holes embedded inside a gap, commonly called a trench. The walls of this gap are commonly vertical with respect to the direction of the main flow and are directly in the path of the coolant. The coolant hits the downstream trench wall which forces it to spread laterally, resulting in more even film coverage downstream than that of regular holes flush with the surface. Recent literature has focused on the effect that trenching has on cylindrical cooling holes only. While the results indicate that trenches are an exciting, promising new geometry derived from the refurbishing process of thermal barrier ceramic coatings, not all the parameters affecting film cooling have been investigated relating to trenched holes. For example, nothing has been said about how far apart holes inside the trench will need to be placed for them to stop interacting. Nothing has been said about shaped holes inside a trench, either. This dissertation explores the extent to which trenching is useful by expanding the PI/D from 4 to 12 for rows of round and fan holes. In addition the effect that trenching has on fan-shaped holes is studied by systematically increasing the trench depth. Values of local, laterally-averaged and spatially-averaged film cooling effectiveness are reported. It is found that placing the cylinders inside the trench and doubling the distance between the holes provides better performance than the cylindrical, non-trenched baseline, especially at the higher blowing ratios, M > 1.0. At these higher coolant flow rates, the regular cylindrical jets show detachment, while those in the trench do not. They, in fact perform very well. The importance of this finding implies that the number of holes, and coolant, can be cut in half while still improving performance over regular holes. The trenched cylindrical holes did not, however, perform like the fan shaped holes. It was found that the performance of fan-shaped holes inside trenches is actually diminished by the presence of the trench. It is obvious, since the fan diffuses the flow, reducing the momentum of the coolant; the addition of the trench further slows the flow down. This, in turn, leads to the quicker ingestion of the main flow by the jets resulting in lower effectiveness. The next part of the study consisted of systematically increasing the depth of the trench for the fan-shaped holes. The purpose of this was to quantify the effect of the trench on the film cooling effectiveness. It was found that the presence of the trench significantly reduces the film effectiveness, especially for the deeper cases. At the higher blowing ratios, the overall performance of the fans collapses to the same value signifying insensitivity to the blowing ratio. A recent study suggests that having a compound angle could reduce the protective effect of the film due to the elevated interaction between the non-co-flowing coolant jet and the mainstream. Although it has been suggested that a non-symmetric lateral diffusion could mitigate the ill effects of having a compound angle, little has been understood on the effect this non-symmetry has on film cooling effectiveness. The last part of this study investigates the effect of non-symmetric lateral diffusion on film cooling effectiveness by systematically varying one side of a fan-shaped hole. For this part of the study, one of the lateral angles of diffusion of a fan-shaped hole was changed from 5° to 13°, while the other side was kept at 7°. It was found that a lower angle of diffusion hurts performance, while a larger diffusion angle improves it. However, the more significant result was that the jet seemed to be slightly turning. This suggests that the jets actually have two regions: one region with reduced momentum, ideal for protecting a large area downstream of the point of injection; and another region with more integrity which could withstand more aggressive main flow conditions. A further study should be conducted for this geometry at compound angles with the main flow to test this theory. The studies conducted show that the temperature sensitive paint technique can be used to study the performance of film cooling holes for various geometries. The studies also show the film cooling performance of novel geometries and explain why, in some cases, such new arrangements are desirable, and in others, how they can hurt performance. The studies also point in the direction of further investigations in order to advance cooling technology to more effective applications and reduced coolant consumption, the main goal of applied turbine cooling research.
Show less
Date Issued: 2009
Identifier: CFE0002831, ucf:48082
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0002831

Title: MULTIOBJECTIVE DESIGN OPTIMIZATION OF GAS TURBINE BLADE WITH EMPHASIS ON INTERNAL COOLING.
Creator: Nagaiah, Narasimha, Geiger, Christopher, Nazzal, Dima, Reilly, Charles, Kapat, Jayanta, University of Central Florida
Abstract / Description: In the design of mechanical components, numerical simulations and experimental methods are commonly used for design creation (or modification) and design optimization. However, a major challenge of using simulation and experimental methods is that they are time-consuming and often cost-prohibitive for the designer. In addition, the simultaneous interactions between aerodynamic, thermodynamic and mechanical integrity objectives for a particular component or set of components are difficult to...
Show moreIn the design of mechanical components, numerical simulations and experimental methods are commonly used for design creation (or modification) and design optimization. However, a major challenge of using simulation and experimental methods is that they are time-consuming and often cost-prohibitive for the designer. In addition, the simultaneous interactions between aerodynamic, thermodynamic and mechanical integrity objectives for a particular component or set of components are difficult to accurately characterize, even with the existing simulation tools and experimental methods. The current research and practice of using numerical simulations and experimental methods do little to address the simultaneous (")satisficing(") of multiple and often conflicting design objectives that influence the performance and geometry of a component. This is particularly the case for gas turbine systems that involve a large number of complex components with complicated geometries.Numerous experimental and numerical studies have demonstrated success in generating effective designs for mechanical components; however, their focus has been primarily on optimizing a single design objective based on a limited set of design variables and associated values. In this research, a multiobjective design optimization framework to solve a set of user-specified design objective functions for mechanical components is proposed. The framework integrates a numerical simulation and a nature-inspired optimization procedure that iteratively perturbs a set of design variables eventually converging to a set of tradeoff design solutions. In this research, a gas turbine engine system is used as the test application for the proposed framework. More specifically, the optimization of the gas turbine blade internal cooling channel configuration is performed. This test application is quite relevant as gas turbine engines serve a critical role in the design of the next-generation power generation facilities around the world. Furthermore, turbine blades require better cooling techniques to increase their cooling effectiveness to cope with the increase in engine operating temperatures extending the useful life of the blades.The performance of the proposed framework is evaluated via a computational study, where a set of common, real-world design objectives and a set of design variables that directly influence the set of objectives are considered. Specifically, three objectives are considered in this study: (1) cooling channel heat transfer coefficient, which measures the rate of heat transfer and the goal is to maximize this value; (2) cooling channel air pressure drop, where the goal is to minimize this value; and (3) cooling channel geometry, specifically the cooling channel cavity area, where the goal is to maximize this value. These objectives, which are conflicting, directly influence the cooling effectiveness of a gas turbine blade and the material usage in its design. The computational results show the proposed optimization framework is able to generate, evaluate and identify thousands of competitive tradeoff designs in a fraction of the time that it would take designers using the traditional simulation tools and experimental methods commonly used for mechanical component design generation. This is a significant step beyond the current research and applications of design optimization to gas turbine blades, specifically, and to mechanical components, in general.
Show less
Date Issued: 2012
Identifier: CFE0004495, ucf:49282
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004495

Title: HEAT TRANSFER AUGMENTATION IN A NARROW RECTANGULAR DUCT WITH DIMPLES APPLIED TO A SINGLE WALL.
Creator: Slabaugh, Carson, Kapat, Jayanta, University of Central Florida
Abstract / Description: Establishing a clean and renewable energy supply is the preeminent engineering challenge of our time. Turbines, in some form, are responsible for more than 98 percent of all electricity generated in the United State and 100 percent of commercial and military air transport. The operation of these engines is clearly responsible for significant consumption of hydrocarbon fuels and, in turn, emission of green house gases into the atmosphere. With such wide-scale implementation, it is understood...
Show moreEstablishing a clean and renewable energy supply is the preeminent engineering challenge of our time. Turbines, in some form, are responsible for more than 98 percent of all electricity generated in the United State and 100 percent of commercial and military air transport. The operation of these engines is clearly responsible for significant consumption of hydrocarbon fuels and, in turn, emission of green house gases into the atmosphere. With such wide-scale implementation, it is understood that even the smallest increase in the operating efficiency of these machines can lead to enormous improvements over the current energy situation. These effects can extend from a reduction in the emission of greenhouse gases to lessening the nationÃ‚Â's dependence of foreign energy sources to lower energy prices for the consumer. The prominent means of increasing engine efficiency is by raising the Ã‚Â'Turbine Inlet TemperatureÃ‚Â' Ã‚Â– the temperature of the mainstream flow after combustion, entering the first stage of the turbine section. The challenge is presented when these temperatures are forced beyond the allowable limits of the materials inside the machine. In order to protect these components, active cooling and protection methods are employed. The focus of this work is the development of more efficient means of cooling Ã‚Â'hotÃ‚Â' turbine components. In doing so, the goal is to maximize the amount of heat removed by the coolant while minimizing the coolant mass flow rate: by removing a greater amount of heat with a lower coolant mass flow rate, more compressed air is left in the mainstream gas flow for combustion and power generation. This study is an investigation of the heat transfer augmentation through the fully-developed portion of a narrow rectangular duct (AR=2) characterized by the application of dimples to the bottom wall of the channel. Experimental testing and numerical modeling is performed for full support and validation of presented findings. The geometries are studied at channel Reynolds numbers of 20000, 30000, and 40000. The purpose is to understand the contribution of dimple geometries in the formation of flow structures that improve the advection of heat away from the channel walls. Experimental data reported includes the local and Nusselt number augmentation of the channel walls and the overall friction augmentation throughout the length of the duct. Computational results validate local Nusselt number results from experiments, in addition to providing further insight to local flow physics causing the observed surface phenomena. By contributing to a clearer understanding of the effects produced by these geometries, the development of more effective channel-cooling designs can be achieved.
Show less
Date Issued: 2010
Identifier: CFE0003223, ucf:48511
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003223

Title: Statistical Analysis of Multi-Row Film Cooling Flowfields.
Creator: Fernandes, Craig, Kapat, Jayanta, Ahmed, Kareem, Vasu Sumathi, Subith, University of Central Florida
Abstract / Description: A huge part of modern day power generation research and development strives to achievehigher thermal efficiencies and specific work outputs for both gas turbine Brayton and combinedcycles. Advances in cooling technologies, both internal to turbine blades and external, provide the easiest way to accomplish this by raising the turbine inlet temperature far beyond the super-alloy's allowable temperature. Discrete film cooling injection, an external cooling technique, ensures a cool blanket of...
Show moreA huge part of modern day power generation research and development strives to achievehigher thermal efficiencies and specific work outputs for both gas turbine Brayton and combinedcycles. Advances in cooling technologies, both internal to turbine blades and external, provide the easiest way to accomplish this by raising the turbine inlet temperature far beyond the super-alloy's allowable temperature. Discrete film cooling injection, an external cooling technique, ensures a cool blanket of compressed air protects the blade surface from the harsh mainstream gas. To optimize the coverage and effectiveness of the film, a thorough understanding of the behavior andflow physics is necessary.The objective of the current study is to use hotwire anemometry as a tool to conduct 1D timeresolved turbulent measurements on the flow field of staggered multi-row film cooling arrays withcylindrical and diffuser shaped holes inclined at 20 degrees to the freestream. The study aims toinvestigate the flowfield to determine why the performance of diffuser shaped jets is enhanced even at comparatively high blowing ratios. In addition, blowing ratio effects and flowfield discrepanciesat set downstream locations in the array centerline plane are also investigated.The experiments are conducted on an open-loop wind tunnel for blowing ratios in the rangeof 0.3 to 1.5 at a density ratio of 1. Boundary layer measurements were taken at 12 locations atthe array centerline to obtain mean velocity, turbulence level, turbulence intensity, and integral length scales. Measurements were also taken at a location upstream of the array to characterize the incoming boundary layer and estimate the wall normal position of the probe in comparison with the logarithmic law of the wall.Mean effective velocity profiles were found to scale with blowing ratio for both geometries.A strong dependence of turbulence levels on velocity gradients between jets and the local fluid was also noticed. For cylindrical jets, attached cases displayed lower integral length scales in the nearwall region compared with higher blowing ratio cases. This was found to be due to entrainmentof mainstream fluid showing increased momentum transport below the jets. Diffuser cases atall blowing ratios tested do not show increased length scales near the wall demonstrating theirenhanced surface coverage. Row-to-row discrepancies in mean velocity and turbulence level are only evident at extremely high blowing cases for cylindrical, but show significant deviations for diffuser cases at all blowing ratios.Unlike the cylindrical cases, jets from diffuser shaped holes, due to their extremely low injecting velocities, dragged the boundary layer with each row of blowing. Increased velocity gradients create a rise in peak turbulence levels at downstream locations. At high blowing ratios however, faster moving fluid, due to injection, at lower elevations acts as a shield for downstream jets allowing significantly further propagation downstream. Near the wall low magnitude integral length scales are noticed for diffuser jets indicating low momentum transport in this region.The results show good agreement with effectiveness measurements of a previous study at a higher density ratio. However, to accurately draw the comparison, effectiveness measurements should be conducted at a density ratio of 1. Recommendations were made to further the study of multi-row film cooled boundary layers. The scope includes a CFD component, other flowfield measurement techniques, and surface effectiveness studies using Nitrogen as the coolant for a much broader picture of this flowfield.
Show less
Date Issued: 2017
Identifier: CFE0006738, ucf:51863
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0006738

Title: Heat Transfer in a Coupled Impingement-Effusion Cooling System.
Creator: Miller, Mark, Kapat, Jayanta, Deng, Weiwei, Gordon, Ali, University of Central Florida
Abstract / Description: The efficiency of air-breathing gas turbine engines improves as the combustion temperature increases. Therefore, modern gas turbines operate at temperatures greater than the melting temperature of hot-gas-path components, and cooling must be introduced in order to maintain mechanical integrity of those components. Two highly effective techniques used in modern designs for this purpose are impingement cooling and use of coolant film on hot-gas-path surface introduced through discrete film or...
Show moreThe efficiency of air-breathing gas turbine engines improves as the combustion temperature increases. Therefore, modern gas turbines operate at temperatures greater than the melting temperature of hot-gas-path components, and cooling must be introduced in order to maintain mechanical integrity of those components. Two highly effective techniques used in modern designs for this purpose are impingement cooling and use of coolant film on hot-gas-path surface introduced through discrete film or effusion holes. In this study, these two mechanisms are coupled into a single prototype cooling system. The heat transfer capability of this system is experimentally determined for a variety of different geometries and coolant flow rates.This study utilizes Temperature Sensitive Paint (TSP) in order to measure temperature distribution over a surface, which allowed for local impingement Nusselt number, film cooling effectiveness, and film cooling heat transfer enhancement profiles to be obtained. In addition to providing quantitative heat transfer data, this method allowed for qualitative investigation of the flow behavior near the test surface. Impinging jet-to-target-plate spacing was varied over a large range, including several tall impingement scenarios outside the published limits. Additionally, both in-line and staggered effusion arrangements were studied, and results for normal injection were compared to full coverage film cooling with inclined- and compound-angle injection. Effects of impingement and effusion cooling were combined to determine the overall cooling effectiveness of the system.It is shown that low impingement heights produce the highest Nusselt number, and that large jet-to-jet spacing reduces coolant flow rate while maintaining moderate to high heat transfer rates. Staggered effusion configurations exhibit superior performance to in-line configurations, as jet interference is reduced and surface area coverage is improved. Coolant to mainstream flow mass flux ratios greater than unity result in jet blow-off and reduced effectiveness. The convective heat transfer coefficient on the film cooled surface is higher than a similar surface without coolant injection due to the generation of turbulence associated with jet-cross flow interaction.
Show less
Date Issued: 2011
Identifier: CFE0004140, ucf:49042
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004140

Title: Hydrodynamic Measurements of the Flow Structure Emanating From A Multi-Row Film Cooling Configuration.
Creator: Voet, Michael, Kapat, Jayanta, Vasu Sumathi, Subith, Ahmed, Kareem, University of Central Florida
Abstract / Description: The demand for more power is rapidly increasing worldwide. Attention is turned to increasingthe efficiency of modern methods for power generation. Gas turbines provide 35% of the powerdemands within the United States. Efficiency of gas turbines is defined in an ideal sense by thethermal efficiency of the Brayton Cycle. The overall efficiency of a gas turbine can be increased while simultaneously maximizing specific work output, by increasing the turbine inlet temperature. However, even with...
Show moreThe demand for more power is rapidly increasing worldwide. Attention is turned to increasingthe efficiency of modern methods for power generation. Gas turbines provide 35% of the powerdemands within the United States. Efficiency of gas turbines is defined in an ideal sense by thethermal efficiency of the Brayton Cycle. The overall efficiency of a gas turbine can be increased while simultaneously maximizing specific work output, by increasing the turbine inlet temperature. However, even with the advancements in modern materials in terms of maximum operatingtemperature, various components are already subjected to temperatures higher than their melting temperatures. An increase in inlet temperature would subject various components to even higher temperatures, such that more effective cooling would be necessary, whilst ideally using the same (or less) amount of cooling air bled from compressor. Improvements in the performance of these cooling techniques is thus required. The focus of this thesis is on one such advanced cooling technique, namely film cooling.The objective of this study is to investigate the effects of coolant density on the jet structure for different multi-row film cooling configurations. As research is performed on improving the performance of film cooling, the available conditions during testing may not reflect actual engine-like conditions. Typical operating density ratio at engine conditions are between 1.5 and 2, while it is observed that a majority of the density ratios tested in literature are between 1 and 1.5. While thesetests may be executed outside of engine-like conditions, it is important to understand how density ratio effects the flow physics and film cooling performance. The density ratio within this study is varied between 1.0 and 1.5 by alternating the injecting fluid between air and Carbon Dioxide, respectively.Both a simple cylindrical and fan-shape multi-row film cooling configuration are tested in the present study. In order to compare the results collected from these geometries, lateral and spanwise hole-to-hole spacing, metering hole diameter, hole length, and inclination angle are held constant between all testing configurations. The effect of fluid density upon injection is examined by independently holding either blowing, momentum flux, or velocity ratio constant whilst varying density ratio. Comparisons between both of the film cooling configurations are also made as similar ratios are tested between geometries. This allows the variation in flow structure and performance to be observed from alternating the film cooling hole shape.Particle Image Velocimetry (PIV) is implemented to obtain both streamwise and wall normal velocitymeasurements for the array centerline plane. This data is used to examine the interactionof the jet as it leaves the film cooling hole and the structure produced when the jet mixes with theboundary layer.Similarities in jet to jet interactions and surface attachment between density ratios are seen for the cylindrical configuration when momentum flux ratio is held constant. When observing constant blowing ratio comparisons of the cylindrical configurations, the lower density ratio is seen to begin detaching from the wall at M = 0.72 with little evidence of coolant in the near wall region. However, the higher density cylindrical injection retains its surface attachment at M = 0.74 with noticeably more coolant near the wall, because of significantly lower momentum flux ratio and lower (")jetting(") effect. The fan-shape film cooling configuration demonstrates improved performance, in terms of surface attachment, over a larger range of all ratios than that of the cylindrical cases. Additionally, the fan-shape configuration is shown to constantly retain a thicker layer of low velocity fluid in the near wall region when injected with the higher density coolant, suggesting improved performance at the higher density ratio.When tracking the jet trajectory, it is shown that the injection of CO2 through the cylindricalconfiguration yields a higher centerline wall normal height per downstream location than that of the lower density fluid. Comparing the results of the centerline tracking produced by the third and fifth rows for both the injection of air and CO2, it is confirmed that the fifth row of injection interacts with the boundary layer at a great wall normal height than that of the third row. Additionally, when observing the change in downstream trajectory between the fifth and seventh row of injection, a significant decrease in wall normal height is seen for the coolant produced by the seventh row. It is believed that the lack of a ninth row of injection allows the coolant from the seventh row of injection to remain closer to the target surface. This is further supported by the observation of the derived pressure gradient field and the path streamlines take while interacting with the recirculatory region produced by the injection of coolant into the boundary layer.Further conclusions are drawn by investigating the interaction between momentum thickness andthe influence of blowing ratio. Relatively constant downstream momentum thickness is observedfor the injection of lower density fluid for the blowing ratio range of M= 0.4 to 0.8 for the cylindrical configuration. It is suggested that a correlation exists between momentum thickness and film cooling performance, however further studies are needed to validate this hypothesis.
Show less
Date Issued: 2017
Identifier: CFE0006817, ucf:51791
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0006817

Title: The Study of an Impinging Unsteady Jet - Fluid Mechanics and Heat Transfer Analysis.
Creator: Osorio, Andrea, Kapat, Jayanta, Kinzel, Michael, Raghavan, Seetha, University of Central Florida
Abstract / Description: The high heat transfer capabilities of impinging jets have led to their widespread use in industrial applications, such as gas turbine cooling. These impinging jets are usually manufactured on the walls of super-alloy metals and are influenced by being positioned with a confined setting. Studies have been shown to enhance the heat transfer of impinging jets by fluctuating the flow which will be analyzed in this project with two designs. The first design is a self-sustaining stationary fluidic...
Show moreThe high heat transfer capabilities of impinging jets have led to their widespread use in industrial applications, such as gas turbine cooling. These impinging jets are usually manufactured on the walls of super-alloy metals and are influenced by being positioned with a confined setting. Studies have been shown to enhance the heat transfer of impinging jets by fluctuating the flow which will be analyzed in this project with two designs. The first design is a self-sustaining stationary fluidic oscillator that causes a sweeping motion jet to impinge on the surface. This is investigated using Particle Image Velocimetry (PIV) to study the flow field as well as copper- block heated surface to study the heat transfer. The second design involves pulsating the jet through a rotating disk that opens and closes the jet hole, providing a pulsing impingement on the surface. This is examined using hot-wire anemometry for understanding the fluid mechanics and copper-block heated surface to study the heat transfer. Both configurations are tested at a constant Reynolds number of 30,000 with the oscillator tested at normalized jet-to-surface spacings of 3, 4, 6 and the pulsing mechanism tested at jet-to-surface spacing of 3. The results for the fluidic oscillator indicate: Reynolds stress profiles of the jet demonstrated elevated levels of mixing for the fluidic oscillator; heat transfer enhancement was seen in some cases; a confined jet does worse than an unconfined case; and the oscillator's heat removal performed best at lower jet-to- surface spacings. The results for the pulsing mechanism indicate: lower frequencies displayed high turbulence right at the exit of the jet as well as the jet-to-surface spacing of 3; the duty cycle parameter strongly influences the heat transfer results; and heat transfer enhancement was seen for a variation of frequencies.
Show less
Date Issued: 2018
Identifier: CFE0007353, ucf:52102
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007353

Title: Analysis of Heat Transfer on Turbulence Generating Ribs using Dynamic Mode Decomposition.
Creator: Elmore, Michael, Kapat, Jayanta, Ahmed, Kareem, Bhattacharya, Samik, University of Central Florida
Abstract / Description: Ducts with turbulence-promoting ribs are common in heat transfer applications. This study usesa recent modal extraction technique called Dynamic Mode Decomposition (DMD) to determinemode shapes of the spatially and temporally complex flowfield inside a ribbed duct. One subjectmissing from current literature is a method of directly linking a mode to a certain engineeringquantity of interest. Presented is a generalized methodology for producing such a link utilizing thedata from the DMD...
Show moreDucts with turbulence-promoting ribs are common in heat transfer applications. This study usesa recent modal extraction technique called Dynamic Mode Decomposition (DMD) to determinemode shapes of the spatially and temporally complex flowfield inside a ribbed duct. One subjectmissing from current literature is a method of directly linking a mode to a certain engineeringquantity of interest. Presented is a generalized methodology for producing such a link utilizing thedata from the DMD analysis. Theory suggests exciting the modes which are identified may causethe flow to change in such a way to promote the quantity of interest, in this case, heat transfer. Thistheory is tested by contouring the walls of the duct by the extracted mode shapes.The test procedure is taken from an industrial perspective. An initial, unmodified geometry pro-vides a baseline for comparison to later contoured models. The initial case is run as a steady-stateReynolds-Averaged Navier-Stokes model. Large-Eddy Simulation generates the necessary datafor the DMD analysis. Several mode shapes extracted from the flow are applied to the duct wallsand run again in the RANS model, then compared to the baseline, and their relative performanceexamined.
Show less
Date Issued: 2018
Identifier: CFE0007328, ucf:52123
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0007328

Title: Development of Full Surface Transient Thermochromic Liquid Crystal Technique for Internal Cooling Channels.
Creator: Tran, Lucky, Kapat, Jayanta, Kassab, Alain, Vasu Sumathi, Subith, University of Central Florida
Abstract / Description: Proper design of high performance industrial heat transfer equipment relies on accurate knowledge and prediction of the thermal boundary conditions. In order to enhance the overall gas turbine efficiency, advancements in cooling technology for gas turbines and related applications are continuously investigated to increase the turbine inlet temperature without compromising the durability of the materials used. For detailed design, local distributions are needed in addition to bulk quantities....
Show moreProper design of high performance industrial heat transfer equipment relies on accurate knowledge and prediction of the thermal boundary conditions. In order to enhance the overall gas turbine efficiency, advancements in cooling technology for gas turbines and related applications are continuously investigated to increase the turbine inlet temperature without compromising the durability of the materials used. For detailed design, local distributions are needed in addition to bulk quantities. Detailed local distributions require advanced experimental techniques whereas they are readily available using numerical tools. Numerical predictions using a computational fluid dynamics approach with popular turbulence models are benchmarked against a semi-empirical correlation for the friction in a circular channel with repeated-rib roughness to demonstrate some shortcomings of the models used. Numerical predictions varied widely depending on the turbulence modelling approach used. The need for a compatible experimental dataset to accompany numerical simulations was discussed.An exact, closed-form analytical solution to the enhanced lumped capacitance model is derived. The temperature evolution in a representative 2D turbulated surface is simulated using Fluent to validate the model and its exact solution. A case including an interface contact resistance was included as well as various rib sizes to test the validity of the model over a range of conditions. The analysis was extended to the inter-rib region to investigate the extent and magnitude of the influence of the metallic rib features on the apparent heat transfer coefficients in the inter-rib region. It was found that the thermal contamination is limited only to the regions closest to the base of the rib feature.An experimental setup was developed, capable of measuring the local heat transfer distributions on all four channel walls of a rectangular channel (with aspect ratios between 1 and 5) at Reynolds numbers up to 150,000. The setup utilizes a transient thermochromic liquid crystals technique using narrow band crystals and a four camera setup. The setup is used to test a square channel with ribs applied to one wall. Using the transient thermochromic liquid crystals technique and applying it underneath high conductivity, metallic surface features, it is possible to calculate the heat transfer coefficient using a lumped heat capacitance approach. The enhanced lumped capacitance model is used to account for heat conduction into the substrate material. Rohacell and aluminum ribs adhered to the surface were used to tandem to validate the hybrid technique against the standard technique. Local data was also used to investigate the effect of thermal contamination. Thermal contamination observed empirically was more optimistic than numerical predictions.Traditional transient thermochromic liquid crystals technique utilizes the time-to-arrival of the peak intensity of the green color signal. The technique has been extended to utilize both the red and green color signals, increasing the throughput by recovering unused data while also allowing for a reduction in the experimental uncertainty of the calculated heat transfer coefficient. The over-determined system was solved using an un-weighted least squares approach. Uncertainty analysis of the multi-color technique demonstrated its superior performance over the single-color technique. The multi-color technique has the advantage of improved experimental uncertainty while being easy to implement.
Show less
Date Issued: 2014
Identifier: CFE0005430, ucf:50436
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0005430

Title: FILM COOLING WITH WAKE PASSING APPLIED TO AN ANNULAR ENDWALL.
Creator: Tran, Nghia, Kapat, Jayanta, University of Central Florida
Abstract / Description: Advancement in turbine technology has far reaching effects on today's society and environment. With more than 90% of electricity and 100% of commercial air transport being produced by the usage of gas turbine, any advancement in turbine technology can have an impact on fuel used, pollutants and carbon dioxide emitted to the environment. Within the turbine engine, fully understanding film cooling is critical to reliability of a turbine engine. Film cooling is an efficient way to protect...
Show moreAdvancement in turbine technology has far reaching effects on today's society and environment. With more than 90% of electricity and 100% of commercial air transport being produced by the usage of gas turbine, any advancement in turbine technology can have an impact on fuel used, pollutants and carbon dioxide emitted to the environment. Within the turbine engine, fully understanding film cooling is critical to reliability of a turbine engine. Film cooling is an efficient way to protect the engine surface from the extremely hot incoming gas, which is at a temperature much higher than allowable temperature of even the most advanced super alloy used in turbine. Film cooling performance is affected by many factors: geometrical factors and as well as flow conditions. In most of the film cooling literature, film effectiveness has been used as criterion to judge and/or compare between film cooling designs. Film uniformity is also a critical factor, since it determines how well the coolant spread out downstream to protect the hot-gas-path surface of a gas turbine engine. Even after consideration of all geometrical factors and flow conditions, the film effectiveness is still affected by the stator-rotor interaction, in particular by the moving wakes produced by upstream airfoils. A complete analysis of end wall film cooling inside turbine is required to fully understand the phenomena. This full analysis is almost impossible in the academic arena. Therefore, a simplified but critical experimental rig and computational fluid model were designed to capture the effect of wake on film cooling inside an annular test section. The moving wakes are created by rotating a wheel with 12 spokes or rods with a variable speed motor. Thus changing the motor speed will alter the wake passing frequency. This design is an advancement over most previous studies in rectangular duct, which cannot simulate wakes in an annular passage as in an engine. This rig also includes film injection that allows study of impact of moving wakes on film cooling. This wake is a simplified representation of the trailing edge created by an upstream airfoil. An annulus with 30Ã‚Â° pitch test section is considered in this study. This experimental rig is based on an existing flat plate film cooling (BFC) rig that has been validated in the past. Measurement of velocity profiles within the moving wake downstream from the wake generator is used to validate the CFD rotating wake model. The open literature on film cooling and past experiments performed in the laboratory validated the CFD film cooling model. With these validations completed, the full CFD model predicts the wake and film cooling interaction. Nine CFD cases were considered by varying the film cooling blowing ratio and the wake Strouhal number. The results indicated that wakes highly enhance film cooling effectiveness near film cooling holes and degrades the film blanket downstream of the film injection, at the moment of wake passing. However, the time-averaged film cooling effectiveness is more or less the same with or without wake.
Show less
Date Issued: 2010
Identifier: CFE0003483, ucf:48956
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003483

Title: Multi-Row Film Cooling Boundary Layers.
Creator: Natsui, Gregory, Kapat, Jayanta, Raghavan, Seetha, Vasu Sumathi, Subith, University of Central Florida
Abstract / Description: High fidelity measurements are necessary to validate existing and future turbulence models for the purpose of producing the next generation of more efficient gas turbines. The objective of the present study is to conduct several different measurements of multi-row film cooling arrays in order to better understand the physics involved with injection of coolant through multiple rows of discrete holes into a flat plate turbulent boundary layer. Adiabatic effectiveness distributions are measured...
Show moreHigh fidelity measurements are necessary to validate existing and future turbulence models for the purpose of producing the next generation of more efficient gas turbines. The objective of the present study is to conduct several different measurements of multi-row film cooling arrays in order to better understand the physics involved with injection of coolant through multiple rows of discrete holes into a flat plate turbulent boundary layer. Adiabatic effectiveness distributions are measured for several multi-row film cooling geometries. The geometries are designed with two different hole spacings and two different hole types to yield four total geometries. One of the four geometries tested for adiabatic effectiveness was selected for flowfield measurements. The wall and flowfield are studied with several testing techniques, including: particle image velocimetry, hot wire anemometry, pressure sensitive paint and discrete gas sampling.
Show less
Date Issued: 2015
Identifier: CFE0005982, ucf:50776
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0005982

Title: FUNDAMENTAL UNDERSTANDING OF INTERACTIONS AMONG FLOW, TURBULENCE, AND HEAT TRANSFER IN JET IMPINGEMENT COOLING.
Creator: Hossain, Md. Jahed, Kapat, Jayanta, Ahmed, Kareem, Gordon, Ali, Wiegand, Rudolf, University of Central Florida
Abstract / Description: The flow physics of impinging jet is very complex and is not fully understood yet. The flow field in an impingement problem comprised of three different distinct regions: a free jet with a potential core, a stagnation region where the velocity goes to zero as the jet impinges onto the wall and a creation of wall jet region where the boundary layer grows radially outward after impinging. Since impingement itself is a broad topic, effort is being made in the current study to narrow down on...
Show moreThe flow physics of impinging jet is very complex and is not fully understood yet. The flow field in an impingement problem comprised of three different distinct regions: a free jet with a potential core, a stagnation region where the velocity goes to zero as the jet impinges onto the wall and a creation of wall jet region where the boundary layer grows radially outward after impinging. Since impingement itself is a broad topic, effort is being made in the current study to narrow down on three particular geometric configurations (a narrow wall, an array impingement configuration and a curved surface impingement configuration) that shows up in a typical gas turbine impingement problem in relation to heat transfer. Impingement problems are difficult to simulate numerically using conventional RANS models. It is worth noting that the typical RANS model contains a number of calibrated constants and these have been formulated with respect to relatively simple shear flows. As a result typically these isotropic eddy viscosity models fail in predicting the correct heat transfer value and trend in impingement problem where the flow is highly anisotropic. The common RANS-based models over predict stagnation heat transfer coefficients by as much as 300% when compared to measured values. Even the best of the models, the v^2-f model, can be inaccurate by up to 30%. Even though there is myriad number of experimental and numerical work published on single jet impingement; the knowledge gathered from these works cannot be applied to real engineering impingement cooling application as the dynamics of flow changes completely. This study underlines the lack of experimental flow physics data in published literature on multiple jet impingement and the author emphasized how important it is to have experimental data to validate CFD tools and to determine the suitability of Large Eddy Simulation (LES) in industrial application. In the open literature there is not enough study where experimental heat transfer and flow physics data are combined to explain the behavior for gas turbine impingement cooling application. Often it is hard to understand the heat transfer behavior due to lack of time accurate flow physics data hence a lot of conjecture has been made to explain the phenomena. The problem is further exacerbated for array of impingement jets where the flow is much more complex than a single round jet. The experimental flow field obtained from Particle Image Velocimetry (PIV) and heat transfer data obtained from Temperature Sensitive Paint (TSP) from this work will be analyzed to understand the relationship between flow characteristics and heat transfer for the three types of novel geometry mentioned above.There has not been any effort made on implementing LES technique on array impingement problem in the published literature. Nowadays with growing computational power and resources CFD are widely used as a design tool. To support the data gathered from the experiment, LES is carried out in narrow wall impingement cooling configuration. The results will provide more accurate information on impingement flow physics phenomena where experimental techniques are limited and the typical RANS models yield erroneous resultThe objective of the current study is to provide a better understanding of impingement heat transfer in relation to flow physics associated with it. As heat transfer is basically a manifestation of the flow and most of the flow in real engineering applications is turbulent, it is very important to understand the dynamics of flow physics in an impingement problem. The work emphasis the importance of understanding mean velocities, turbulence, jet shear layer instability and its importance in heat transfer application. The present work shows detailed information of flow phenomena using Particle Image Velocimetry (PIV) in a single row narrow impingement channel. Results from the RANS and LES simulations are compared with Particle Image Velocimetry (PIV) data. The accuracy of LES in predicting the flow field and heat transfer of an impingement problem is also presented the in the current work as it is validated against experimental flow field measured through PIV.Results obtained from the PIV and LES shows excellent agreement for predicting both heat transfer and flow physics data. Some of the key findings from the study highlight the shortcomings of the typical RANS models used for the impingement heat transfer problem. It was found that the stagnation point heat transfer was over predicted by as much as 48% from RANS simulations when compared to the experimental data. A lot of conjecture has been made in the past for RANS' ability to predict the stagnation point heat transfer correctly. The length of the potential core for the first jet was found to be ~ 2D in RANS simulations as oppose to 1D in PIV and LES, confirm the possible underlying reason for this discrepancy. The jet shear layer thickness was underpredicted by ~ 40% in RANS simulations proving the model is not diffusive enough for a flow like jet impingement. Turbulence production due to shear stress was over predicted by ~130% and turbulence production due to normal stresses were underpredicted by ~40 % in RANS simulation very close to the target wall showing RANS models fail where both strain rate and shear stress plays a pivotal role in the dynamics of the flow. In the closing, turbulence is still one of the most difficult problems to solve accurately, as has been the case for about a century. A quote below from the famous mathematician, Horace Lamb (1849-1934) express the level of difficulty and frustration associated with understanding turbulence in fluid mechanics. (")I am an old man now, and when I die and go to heaven there are two matters on which I hope for enlightenment. One is quantum electrodynamics, and the other is the turbulent motion of fluids. And about the former I am rather optimistic.(")Source: http://scienceworld.wolfram.com/biography/Lamb.htmlThis dissertation is expected to shed some light onto one specific example of turbulent flows.
Show less
Date Issued: 2016
Identifier: CFE0006463, ucf:51424
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0006463

heat transfer (7)	+ -
Gas Turbine (6)	+ -
Film Cooling (4)	+ -
Heat Transfer (4)	+ -
film cooling (3)	+ -

gas turbine (3)	+ -
gas turbine cooling (3)	+ -
gas turbines (3)	+ -
Experimental (2)	+ -
Particle Image Velocimetry (2)	+ -
TSP (2)	+ -
computational fluid dynamics (2)	+ -
internal cooling (2)	+ -
jet impingement (2)	+ -
ASYMMETRIC (1)	+ -
Aerodynamics (1)	+ -
Annular Test Section (1)	+ -
Annulus (1)	+ -
Blowing Ratio (1)	+ -
Boundary Layer (1)	+ -
CFD (1)	+ -
Computational Fluid Dynamic (1)	+ -
Computational Fluid Dynamics (CFD) (1)	+ -
Cooling Technique (1)	+ -
Dimples (1)	+ -
Dynamic Mode Decomposition (1)	+ -
ENERGY (1)	+ -
Endwall Film Cooling (1)	+ -
FILM COOLING (1)	+ -
Film Cooling Effectiveness (1)	+ -

University of Central Florida (17)	+ -
Kapat, Jayanta (16)	+ -
Vasu Sumathi, Subith (6)	+ -
Ahmed, Kareem (5)	+ -
Gordon, Ali (3)	+ -

Deng, Weiwei (2)	+ -
Kassab, Alain (2)	+ -
Raghavan, Seetha (2)	+ -
Bhattacharya, Samik (1)	+ -
Durham, Michael Glenn (1)	+ -
Elmore, Michael (1)	+ -
Fernandes, Craig (1)	+ -
Geiger, Christopher (1)	+ -
Harrington, John (1)	+ -
Hodges, Justin (1)	+ -
Hossain, Md. Jahed (1)	+ -
Kapat, Jay (1)	+ -
Kinzel, Michael (1)	+ -
Liu, Quan (1)	+ -
Miller, Mark (1)	+ -
Nagaiah, Narasimha (1)	+ -
Natsui, Gregory (1)	+ -
Nazzal, Dima (1)	+ -
Osorio, Andrea (1)	+ -
Reilly, Charles (1)	+ -
Slabaugh, Carson (1)	+ -
Tran, Lucky (1)	+ -
Tran, Nghia (1)	+ -
Valentino, Michelle (1)	+ -
Voet, Michael (1)	+ -

Search In

Sort Results By:

Narrow results by:

Topical Subject

Collection

Type of Resource

Language

Creator

Format

Owner