View All Items
- Title
- Synthesis and Properties of Self-Assembled C/SiCN Nanocomposite Derived from Polymer Precursors.
- Creator
-
Li, Cheng, An, Linan, Fang, Jiyu, Coffey, Kevin, Liao, Yi, Xu, Chengying, Zhai, Lei, University of Central Florida
- Abstract / Description
-
The properties of C/SiCN nanocomposites synthesized by thermal decomposition of polymer precursors were studied in this work. The novel polymer-to-ceramic process enables us to tailor the ceramic structure in atomic level by designing the starting chemicals and pyrolysis procedures. It is of both fundamental and practical significance to investigate the properties and structures relationship of the nanocomposites. In this work, we explored their application potential in using as anode of...
Show moreThe properties of C/SiCN nanocomposites synthesized by thermal decomposition of polymer precursors were studied in this work. The novel polymer-to-ceramic process enables us to tailor the ceramic structure in atomic level by designing the starting chemicals and pyrolysis procedures. It is of both fundamental and practical significance to investigate the properties and structures relationship of the nanocomposites. In this work, we explored their application potential in using as anode of lithium-ion secondary batteries. The structure and structural evolution of C/SiCN nanocomposite were investigated by using XRD, FTIR, SEM, TEM, Solid state NMR and Raman spectroscopy. The results revealed the nanocomposites consisted of amorphous SiCxNx-4 matrix and carbon nanoclusters distributed within it. The size of the carbon was measured by Raman spectroscopy, varied with starting chemicals and pyrolysis temperature. The electronic properties of the C/SiCN nanocomposite were studied by measuring the I-V curves and a.c. impedance. The d.c. conductivity increased with carbon content and pyrolysis temperatures. The impedance spectra and fitted equivalent circuit results confirmed the existence of two phases in the nanocomposite. The possibility of using C/SiCN as anode in lithium-ion secondary batteries was investigated by electrochemical measurements, namely cyclic voltammetry, galvanostatic cyclic test and electrochemical impedance spectroscopy. The galvanostatic measurements showed that the nanocomposite with 26% of carbon nanoclusters exhibited a specific capacity of 480 mAh/g, which is 30% higher than that of commercial graphite anode. The high capacity of the nanocomposites is attributed to the formation of a novel structure around C/SiCN interface. The excellent electrochemical properties, together with the simple, low-cost processing, make the nanocomposites very promising for Li-ion battery applications.
Show less - Date Issued
- 2012
- Identifier
- CFE0004194, ucf:49028
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0004194
- Title
- Synthesis, Processing and Characterization of Polymer Derived Ceramic Nanocomposite Coating Reinforced with Carbon Nanotube Preforms.
- Creator
-
Yang, Hongjiang, Gou, Jihua, Xu, Yunjun, Lin, Kuo-Chi, University of Central Florida
- Abstract / Description
-
Ceramics have a number of applications as coating material due to their high hardness, wear and corrosion resistance, and the ability to withstand high temperatures. Critical to the success of these materials is the effective heat transfer through a material to allow for heat diffusion or effective cooling, which is often limited by the low thermal conductivity of many ceramic materials. To meet the challenge of improving the thermal conductivity of ceramics without lowering their performance...
Show moreCeramics have a number of applications as coating material due to their high hardness, wear and corrosion resistance, and the ability to withstand high temperatures. Critical to the success of these materials is the effective heat transfer through a material to allow for heat diffusion or effective cooling, which is often limited by the low thermal conductivity of many ceramic materials. To meet the challenge of improving the thermal conductivity of ceramics without lowering their performance envelope, carbon nanotubes were selected to improve the mechanical properties and thermal dispersion ability due to its excellent mechanical properties and high thermal conductivity in axial direction. However, the enhancements are far lower than expectation resulting from limited carbon nanotube content in ceramic matrix composites and the lack of alignment. These problems can be overcome if ceramic coatings are reinforced by carbon nanotubes with good dispersion and alignment. In this study, the well-dispersed and aligned carbon nanotubes preforms were achieved in the form of vertically aligned carbon nanotubes (VACNTs) and Buckypaper. Polymer derived ceramic (PDC) was selected as the matrix to fabricate carbon nanotube reinforced ceramic nanocomposites through resin curing and pyrolysis. The SEM images indicates the alignment of carbon nanotubes in the PDC nanocomposites. The mechanical and thermal properties of the PDC nanocomposites were characterized through Vickers hardness measurement and Thermogravimetric Analysis. The ideal anisotropic properties of nanocomposites were confirmed by estimating the electrical conductivity in two orthogonal directions.
Show less - Date Issued
- 2014
- Identifier
- CFE0005446, ucf:50385
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0005446
- Title
- NOVEL CONCEPTUAL DESIGN AND ANLYSIS OF POLYMER DERIVED CERAMIC MEMS SENSORS FOR GAS TURBINE ENVIRONMENT.
- Creator
-
Nagaiah, Narasimha, Kapat, Jay, University of Central Florida
- Abstract / Description
-
Technical challenges for developing micro sensors for Ultra High Temperature and turbine applications lie in that the sensors have to survive extremely harsh working conditions that exist when converting fuel to energy. These conditions include high temperatures (500-1500°C), elevated pressures (200-400 psi), pressure oscillations, corrosive environments (oxidizing conditions, gaseous alkali, and water vapors), surface coating or fouling, and high particulate loading. Several technologies are...
Show moreTechnical challenges for developing micro sensors for Ultra High Temperature and turbine applications lie in that the sensors have to survive extremely harsh working conditions that exist when converting fuel to energy. These conditions include high temperatures (500-1500°C), elevated pressures (200-400 psi), pressure oscillations, corrosive environments (oxidizing conditions, gaseous alkali, and water vapors), surface coating or fouling, and high particulate loading. Several technologies are currently underdeveloped for measuring these parameters in turbine engines. One of them is an optical-based non-contact technology. However, these nondirective measuring technologies lack the necessary accuracy, at least at present state. An alternative way to measure these parameters without disturbing the working environments is using MEMS type sensors. Currently, the techniques under development for such harsh environment applications are silicon carbide (SiC) and silicon nitrite (Si3N4) based ceramic MEMS sensors. But those technologies present some limitation such as narrow processing method, high cost (materials and processing cost), and limited using temperatures (typically < 800 C). In this research we propose to develop two sensors based on recently developed polymer-derived ceramics (PDCs): Constant Temperature Hot wire Anemometer, temperature/heat-flux sensor for turbine applications. PDC is a new class of high temperature ceramics. As we shall describe below, many unique features of PDCs make them particularly suitable for the proposed sensors, including: excellent thermo-mechanical properties at high temperatures, enable high temperature operation of the devices; various well-developed processing technologies, such as injection molding,photolithography, embossing, DRIE etching and precise machining, can be used for the fabrication of the devices; and tunable electric conductivity, enable the proposed sensors fabricated from similar materials, thus reliability considerations associated with thermal mismatch, which is a big concern when using MEMS-based sensors at elevated temperatures, will be minimized.
Show less - Date Issued
- 2006
- Identifier
- CFE0001285, ucf:46892
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0001285