Current Search:   Youngquist, Robert (x)

View All Items

  • CSV Spreadsheet
(1 - 6 of 6)
The safe removal of frozen air from the annulus of a liquid hydrogen storage tank
Title
The safe removal of frozen air from the annulus of a liquid hydrogen storage tank.
Creator
Krenn, Angela, Bhattacharya, Aniket, Youngquist, Robert, Vasu Sumathi, Subith, University of Central Florida
Abstract / Description
Large Liquid Hydrogen (LH2) storage tanks are vital infrastructure for NASA. Eventually, air may leak into the evacuated and perlite filled annular region of these tanks. Although the vacuum level is monitored in this region, the extremely cold temperature causes all but the helium and neon constituents of air to freeze. A small, often unnoticeable pressure rise is the result. As the leak persists, the quantity of frozen air increases, as does the thermal conductivity of the insulation system...
Show moreLarge Liquid Hydrogen (LH2) storage tanks are vital infrastructure for NASA. Eventually, air may leak into the evacuated and perlite filled annular region of these tanks. Although the vacuum level is monitored in this region, the extremely cold temperature causes all but the helium and neon constituents of air to freeze. A small, often unnoticeable pressure rise is the result. As the leak persists, the quantity of frozen air increases, as does the thermal conductivity of the insulation system. Consequently, a notable increase in commodity boiloff is often the first indicator of an air leak. Severe damage can then result from normal draining of the tank. The warming air will sublimate which will cause a pressure rise in the annulus. When the pressure increases above the triple point, the frozen air will begin to melt and migrate downward. Collection of liquid air on the carbon steel outer shell may chill it below its ductility range, resulting in fracture. In order to avoid a structural failure, as described above, a method for the safe removal of frozen air is needed. Two potential methods for air removal are evaluated here. The first method discussed is the connection of a vacuum pump to the annulus which provides pumping in parallel with drainage of LH2. The goal is to keep the annular pressure below the triple point so that the air continues to sublimate, thus eliminating the threat that liquefaction poses. The second method discussed is the application of heat to the bottom of the outer tank during tank drain. Though liquefaction in the annular space will occur, the goal of the heater design is to keep the outer shell above the embrittlement temperature, so that cracking will not occur.In order to evaluate these methods, it is first necessary to characterize some the physical properties and changes that take place in the system. A thermal model of the storage tank was created in SINDA/FLUINT (C(&)R Technologies, 2014) to identify locations where air can freeze. This model shows the volume that is capable of freezing air under varying conditions. It is also necessary to characterize the changes in thermal conductivity of perlite which has nitrogen frozen into its interstitial spaces. The details and results of an experiment designed for that purpose is outlined. All data, including operational data from existing LH2 tanks, is compiled and a physics-based evaluation of the two proposed air removal techniques is performed.Due to small pumping capacities at low pressure and the large quantity of air inside the annulus, the pumping option is not deemed feasible. It would take many years to remove a significant amount of air by pumping while maintaining the annular pressure below the necessary triple point. Application of heating devices is a feasible option. For a specific case, it is shown that approximately 105 kilowatts of power would be required to vaporize the air in the annulus and keep the temperature of the outer tank wall above the freezing point of water. Several engineering solutions to accomplish this are also discussed. There are many unknowns and complexities in addressing the problem of safely removing frozen air from the annulus of an LH2 storage sphere. The work that follows utilized: research, modeling, experimentation, analysis, and data from existing tanks to arrive at possible solutions to the problem. Heating solutions may be implemented immediately and could result in significant savings to the user.
Show less
Date Issued
2015
Identifier
CFE0005969, ucf:50766
Format
Document (PDF)
PURL
http://purl.flvc.org/ucf/fd/CFE0005969
Programmable Low Loss Orthogonal Frequency Coded Surface Acoustic Wave Correlator Filters
Title
Programmable Low Loss Orthogonal Frequency Coded Surface Acoustic Wave Correlator Filters.
Creator
Smith, Marshall, Malocha, Donald, Weeks, Arthur, Sundaram, Kalpathy, Richie, Samuel, Youngquist, Robert, University of Central Florida
Abstract / Description
Simultaneous Transmit and Receive (STAR) communication is being developed as a means of improving spectral efficiency in wireless communication systems. If the obstacle of self-interference can be sufficiently overcome, it is possible to double the spectral efficiency of an equivalent time or frequency division duplexed system. Spread spectrum techniques can reduce self-interference by using orthogonal or pseudo-orthogonal codes to encode the transmit signal and decode the receive signal...
Show moreSimultaneous Transmit and Receive (STAR) communication is being developed as a means of improving spectral efficiency in wireless communication systems. If the obstacle of self-interference can be sufficiently overcome, it is possible to double the spectral efficiency of an equivalent time or frequency division duplexed system. Spread spectrum techniques can reduce self-interference by using orthogonal or pseudo-orthogonal codes to encode the transmit signal and decode the receive signal.Hardware correlator filters are developed for use with STAR radio systems using orthogonal frequency coded (OFC) surface acoustic wave (SAW) devices. OFC is a type of spread spectrum communication that can be implemented using SAW transducers to create a correlator filter, also known as a matched filter. OFC allows code division multiple access and processing gain, similar to other spread spectrum techniques, but is more well-suited to low loss inline SAW design due to the use of multiple orthogonal carriers.The development of low loss fixed code OFC SAW correlator filters is documented, including design criteria and multiple approaches that progressively reduce insertion loss. Using the results from progressive designs and experiments, a pair of correlator filters with matched codes are presented with approximately 6 dB insertion loss at 950 MHz.A second development focusing on OFC SAW correlator filters with programmable codes using RF switches is also described. The programmable correlators use a fixed OFC code with programmable binary phase shift keying (BPSK), and demonstrate positive results. The programmable correlators presented require less than 1 mW of DC power.
Show less
Date Issued
2018
Identifier
CFE0007768, ucf:52372
Format
Document (PDF)
PURL
http://purl.flvc.org/ucf/fd/CFE0007768
Surface Acoustic Wave (SAW) Cryogenic Liquid and Hydrogen Gas Sensors
Title
Surface Acoustic Wave (SAW) Cryogenic Liquid and Hydrogen Gas Sensors.
Creator
Fisher, Brian, Malocha, Donald, Gong, Xun, Likamwa, Patrick, Richie, Samuel, Youngquist, Robert, University of Central Florida
Abstract / Description
This research was born from NASA Kennedy Space Center's (KSC) need for passive, wireless and individually distinguishable cryogenic liquid and H2 gas sensors in various facilities. The risks of catastrophic accidents, associated with the storage and use of cryogenic fluids may be minimized by constant monitoring. Accidents involving the release of H2 gas or LH2 were responsible for 81% of total accidents in the aerospace industry. These problems may be mitigated by the implementation of a...
Show moreThis research was born from NASA Kennedy Space Center's (KSC) need for passive, wireless and individually distinguishable cryogenic liquid and H2 gas sensors in various facilities. The risks of catastrophic accidents, associated with the storage and use of cryogenic fluids may be minimized by constant monitoring. Accidents involving the release of H2 gas or LH2 were responsible for 81% of total accidents in the aerospace industry. These problems may be mitigated by the implementation of a passive (or low-power), wireless, gas detection system, which continuously monitors multiple nodes and reports temperature and H2 gas presence. Passive, wireless, cryogenic liquid level and hydrogen (H2) gas sensors were developed on a platform technology called Orthogonal Frequency Coded (OFC) surface acoustic wave (SAW) radio frequency identification (RFID) tag sensors. The OFC-SAW was shown to be mechanically resistant to failure due to thermal shock from repeated cycles between room to liquid nitrogen temperature. This suggests that these tags are ideal for integration into cryogenic Dewar environments for the purposes of cryogenic liquid level detection. Three OFC-SAW H2 gas sensors were simultaneously wirelessly interrogated while being exposed to various flow rates of H2 gas. Rapid H2 detection was achieved for flow rates as low as 1ccm of a 2% H2, 98% N2 mixture. A novel method and theory to extract the electrical and mechanical properties of a semiconducting and high conductivity thin-film using SAW amplitude and velocity dispersion measurements were also developed. The SAW device was shown to be a useful tool in analysis and characterization of ultrathin and thin films and physical phenomena such as gas adsorption and desorption mechanisms.?
Show less
Date Issued
2012
Identifier
CFE0004536, ucf:49258
Format
Document (PDF)
PURL
http://purl.flvc.org/ucf/fd/CFE0004536
Multi-transit echo suppression for passive wireless surface acoustic wave sensors using 3rd harmonic unidirectional transducers and Walsh-Hadamard-like reflectors
Title
Multi-transit echo suppression for passive wireless surface acoustic wave sensors using 3rd harmonic unidirectional transducers and Walsh-Hadamard-like reflectors.
Creator
Rodriguez Cordoves, Luis, Malocha, Donald, Weeks, Arthur, Abdolvand, Reza, Moharam, Jim, Youngquist, Robert, University of Central Florida
Abstract / Description
A passive wireless surface acoustic wave sensor of a delay-line type is composed of an antenna, a transducer that converts the EM signal into a surface acoustic wave, and a set of acoustic reflectors that reflect the incoming signal back out through the antenna. A cavity forms between the transducer and the reflectors, trapping energy and causing multiple unwanted echoes. The work in this dissertation aims to reduce the unwanted echoes so that only the main transit signal is left(-)the signal...
Show moreA passive wireless surface acoustic wave sensor of a delay-line type is composed of an antenna, a transducer that converts the EM signal into a surface acoustic wave, and a set of acoustic reflectors that reflect the incoming signal back out through the antenna. A cavity forms between the transducer and the reflectors, trapping energy and causing multiple unwanted echoes. The work in this dissertation aims to reduce the unwanted echoes so that only the main transit signal is left(-)the signal of interest with sensor information.The contributions of this dissertation include reflective delay-line device response in the form of an infinite impulse response (IIR) filter. This may be used in the future to subtract out unwanted echoes via post-processing. However, this dissertation will use a physical approach to echo suppression by using a unidirectional transducer. Thus a unidirectional transducer is used and also optimized for 3rd harmonic operation. Both the directionality and the coupling of the 3rd harmonic optimized SPUDT are improved over a standard electrode width controlled (EWC) SPUDT. New type of reflectors for the reflective delay-line device are also presented. These use BPSK type coding, similar to that of the Walsh-Hadamard codes. Two types are presented, variable reflectivity and variable chip-lengths. The COM model is used to simulate devices and compare the predicted echo suppression level to that of fabricated devices. Finally, a device is mounted on a tunable antenna and the echo is suppressed on a wireless operating device.
Show less
Date Issued
2017
Identifier
CFE0006912, ucf:51697
Format
Document (PDF)
PURL
http://purl.flvc.org/ucf/fd/CFE0006912
Ultra-wideband Spread Spectrum Communications using Software Defined Radio and Surface Acoustic Wave Correlators
Title
Ultra-wideband Spread Spectrum Communications using Software Defined Radio and Surface Acoustic Wave Correlators.
Creator
Gallagher, Daniel, Malocha, Donald, Delfyett, Peter, Richie, Samuel, Weeks, Arthur, Youngquist, Robert, University of Central Florida
Abstract / Description
Ultra-wideband (UWB) communication technology offers inherent advantages such as the ability to coexist with previously allocated Federal Communications Commission (FCC) frequencies, simple transceiver architecture, and high performance in noisy environments. Spread spectrum techniques offer additional improvements beyond the conventional pulse-based UWB communications. This dissertation implements a multiple-access UWB communication system using a surface acoustic wave (SAW) correlator...
Show moreUltra-wideband (UWB) communication technology offers inherent advantages such as the ability to coexist with previously allocated Federal Communications Commission (FCC) frequencies, simple transceiver architecture, and high performance in noisy environments. Spread spectrum techniques offer additional improvements beyond the conventional pulse-based UWB communications. This dissertation implements a multiple-access UWB communication system using a surface acoustic wave (SAW) correlator receiver with orthogonal frequency coding and software defined radio (SDR) base station transmitter.Orthogonal frequency coding (OFC) and pseudorandom noise (PN) coding provide a means for spreading of the UWB data. The use of orthogonal frequency coding (OFC) increases the correlator processing gain (PG) beyond that of code division multiple access (CDMA); providing added code diversity, improved pulse ambiguity, and superior performance in noisy environments. Use of SAW correlators reduces the complexity and power requirements of the receiver architecture by eliminating many of the components needed and reducing the signal processing and timing requirements necessary for digital matched filtering of the complex spreading signal.The OFC receiver correlator code sequence is hard-coded in the device due to the physical SAW implementation. The use of modern SDR forms a dynamic base station architecture which is able to programmatically generate a digitally modulated transmit signal. An embedded Xilinx Zynq (TM) system on chip (SoC) technology was used to implement the SDR system; taking advantage of recent advances in digital-to-analog converter (DAC) sampling rates. SDR waveform samples are generated in baseband in-phase and quadrature (I (&) Q) pairs and upconverted to a 491.52 MHz operational frequency.The development of the OFC SAW correlator ultimately used in the receiver is presented along with a variety of advanced SAW correlator device embodiments. Each SAW correlator device was fabricated on lithium niobate (LiNbO3) with fractional bandwidths in excess of 20%. The SAW correlator device presented for use in system was implemented with a center frequency of 491.52 MHz; matching SDR transmit frequency. Parasitic electromagnetic feedthrough becomes problematic in the packaged SAW correlator after packaging and fixturing due to the wide bandwidths and high operational frequency. The techniques for reduction of parasitic feedthrough are discussedwith before and after results showing approximately 10:1 improvement.Correlation and demodulation results are presented using the SAW correlator receiver under operation in an UWB communication system. Bipolar phase shift keying (BPSK) techniques demonstrate OFC modulation and demodulation for a test binary bit sequence. Matched OFC code reception is compared to a mismatched, or cross-correlated, sequence after correlation and demodulation. Finally, the signal-to-noise power ratio (SNR) performance results for the SAW correlator under corruption of a wideband noise source are presented.
Show less
Date Issued
2015
Identifier
CFE0005794, ucf:50054
Format
Document (PDF)
PURL
http://purl.flvc.org/ucf/fd/CFE0005794
Design, Fabrication, and Interrogation of Integrated Wireless SAW Temperature Sensors
Title
Design, Fabrication, and Interrogation of Integrated Wireless SAW Temperature Sensors.
Creator
Gallagher, Mark, Malocha, Donald, Richie, Samuel, Weeks, Arthur, Youngquist, Robert, Delfyett, Peter, University of Central Florida
Abstract / Description
Wireless surface acoustic wave (SAW) sensors offer unique advantages over other sensor technologies because of their inherent ability to operate in harsh environments and completely passive operation, providing a reliable, maintenance-free life cycle. For certain SAW sensor applications the challenge is building a wirelessly interrogatable device with the same lifetime as the SAW substrate. The design of these application intensive sensors is complicated by the degradation of device bond...
Show moreWireless surface acoustic wave (SAW) sensors offer unique advantages over other sensor technologies because of their inherent ability to operate in harsh environments and completely passive operation, providing a reliable, maintenance-free life cycle. For certain SAW sensor applications the challenge is building a wirelessly interrogatable device with the same lifetime as the SAW substrate. The design of these application intensive sensors is complicated by the degradation of device bond wires, die adhesive, and antenna substrate. In an effort to maximize the benefits of the platform, this dissertation demonstrates wafer-level integrated SAW sensors that directly connect the thin film SAW to a thick film on-wafer antenna. Fully integrated device embodiments are presented that operate over a wide range of temperatures using different fabrication techniques, substrates, and coding principles.
Show less
Date Issued
2015
Identifier
CFE0005795, ucf:50047
Format
Document (PDF)
PURL
http://purl.flvc.org/ucf/fd/CFE0005795