View All Items
(21 - 30 of 30)
Pages
- Title
- Light Trapping in Thin Film Crystalline Silicon Solar Cells.
- Creator
-
Boroumand Azad, Javaneh, Chanda, Debashis, Peale, Robert, Del Barco, Enrique, Flitsiyan, Elena, Schoenfeld, Winston, University of Central Florida
- Abstract / Description
-
This dissertation presents numerical and experimental studies of a unified light trapping approach that is extremely important for all practical solar cells. A 2D hexagonal Bravais lattice diffractive pattern is studied in conjunction with the verification of the reflection mechanisms of single and double layer anti-reflective coatings in the broad range of wavelength 400 nm - 1100 nm. By varying thickness and conformity, we obtained the optimal parameters which minimize the broadband...
Show moreThis dissertation presents numerical and experimental studies of a unified light trapping approach that is extremely important for all practical solar cells. A 2D hexagonal Bravais lattice diffractive pattern is studied in conjunction with the verification of the reflection mechanisms of single and double layer anti-reflective coatings in the broad range of wavelength 400 nm - 1100 nm. By varying thickness and conformity, we obtained the optimal parameters which minimize the broadband reflection from the nanostructured crystalline silicon surface over a wide range of angle 0(&)deg;-65(&)deg;. While the analytical design of broadband, angle independent anti-reflection coatings on nanostructured surfaces remains a scientific challenge, numerical optimization proves a viable alternative, paving the path towards practical implementation of the light trapping solar cells. A 3 (&)#181;m thick light trapping solar cell is modeled in order to predict and maximize combined electron-photon harvesting in ultrathin crystalline silicon solar cells. It is shown that the higher charge carrier generation and collection in this design compensates the absorption and recombination losses and ultimately results in an increase in energy conversion efficiency. Further, 20 (&)#181;m and 100 (&)#181;m thick functional solar cells with the light trapping scheme are studied. The efficiency improvement is observed numerically and experimentally due to photon absorption enhancement in the light trapping cells with respect to a bare cell of same thickness.
Show less - Date Issued
- 2017
- Identifier
- CFE0006936, ucf:51654
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0006936
- Title
- Identification of proteins regulating VLDL sorting into the VLDL Transport Vesicle (VTV) and involved in the biogenesis of the VTV.
- Creator
-
Tiwari, Samata, Siddiqi, Shadab, Zervos, Antonis, Singla, Dinender, Naser, Saleh, University of Central Florida
- Abstract / Description
-
Increased secretion of very low-density lipoprotein (VLDL), a triglyceride-rich lipoprotein, by the liver causes hypertriglyceridemia, which is a major risk factor for the development of atherosclerosis. The rate of VLDL-secretion from the liver is determined by its controlled transport from the endoplasmic reticulum (ER) to the Golgi. The ER-to-Golgi transport of newly synthesized VLDL is a complex multi-step process and is mediated by the VLDL transport vesicle (VTV). Once a nascent VLDL...
Show moreIncreased secretion of very low-density lipoprotein (VLDL), a triglyceride-rich lipoprotein, by the liver causes hypertriglyceridemia, which is a major risk factor for the development of atherosclerosis. The rate of VLDL-secretion from the liver is determined by its controlled transport from the endoplasmic reticulum (ER) to the Golgi. The ER-to-Golgi transport of newly synthesized VLDL is a complex multi-step process and is mediated by the VLDL transport vesicle (VTV). Once a nascent VLDL particle is synthesized in the lumen of the ER, it triggers the process of VTV-biogenesis and this process requires coat complex II (COPII) proteins that mediate the formation of classical protein transport vesicles (PTV). Even though, both VTV and PTV bud off the same ER at the same time and require the same COPII proteins, their cargos and sizes are different. The VTV specifically exports VLDL to the Golgi and excludes hepatic secretory proteins such as albumin and the size of the VTV is larger (~ 100 -120 nm) than PTV to accommodate VLDL-sized particles. These observations indicate (i) the existence of a sorting mechanism at the level of the ER; and (ii) the involvement of proteins in addition to COPII components. This doctoral thesis is focused on identification of proteins regulating VLDL sorting into the VTV and involved in the biogenesis of the VTV. In order to identify proteins present exclusively in VTV, we have characterized the proteome of VTV, which suggest CideB (cell death-inducing DFF45-like effector b) and SVIP (small VCP/P97 interacting protein) as candidates, present in VTV but excluded from PTV. We further confirmed the finding by performing co-immunoprecipitation studies and confocal microscopy studies. CideB, a 26-kDa protein was found to interact with apolipoprotein B100 (apoB 100), the structural protein of VLDL. Moreover, CideB interacts with two of the COPII components, Sar1 and Sec24. VTV generation was examined after blocking CideB by specific antibodies and by silencing CideB in rat primary hepatocytes. Knockdown of CideB in primary hepatocytes showed significant reduction in VTV generation, however, CideB was concentrated in VTV as compared with the ER suggesting its functional role in the sorting of VLDL into the VTV. SVIP, a small (~ 9-kDa) protein was found to interact with Sar1, a COPII component that initiates the budding of vesicles from ER membrane. SVIP has sites for myristoylation and we found increased recruitment of SVIP on ER membrane upon myristic acid (MA) treatment. Sar1 that lacks sites for myristoylation also is recruited more on ER upon myristoylation indicating that SVIP promotes Sar1 recruitment on ER. Additionally, our data suggest that Sar1 interacts with SVIP and forms a multimer that facilitates the biogenesis of VTV. Interestingly, silencing of SVIP reduced the VTV generation significantly. Conversely, incubation with MA increased the VTV budding, suggesting recruitment of SVIP on ER surface facilitates the VTV budding. We conclude that SVIP recruits Sar1 on ER membrane and makes an intricate COPII coat leading to the formation of a large vesicle, the VTV. Overall, the data presented in this thesis, determines the role of CideB and SVIP in regulating VLDL sorting and VTV biogenesis.
Show less - Date Issued
- 2013
- Identifier
- CFE0005270, ucf:50553
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0005270
- Title
- In-situ synchrotron studies of turbine blade thermal barrier coatings under extreme environments.
- Creator
-
Knipe, Kevin, Raghavan, Seetha, Gordon, Ali, Kapat, Jayanta, Sohn, Yongho, University of Central Florida
- Abstract / Description
-
Thermal Barrier Coatings have been used for decades to impose a thermal gradient between the hot combustion gases and the underlying superalloy substrate in engine turbine blades. Yttria Stabilized Zirconia (YSZ) is an industry standard high temperature ceramic for turbine applications. The protective coating is adhered to the substrate using a nickel based alloy bond coat. Through exposure to high temperature, a Thermally Grown Oxide (TGO) layer develops at the bond coat-YSZ interface. Large...
Show moreThermal Barrier Coatings have been used for decades to impose a thermal gradient between the hot combustion gases and the underlying superalloy substrate in engine turbine blades. Yttria Stabilized Zirconia (YSZ) is an industry standard high temperature ceramic for turbine applications. The protective coating is adhered to the substrate using a nickel based alloy bond coat. Through exposure to high temperature, a Thermally Grown Oxide (TGO) layer develops at the bond coat-YSZ interface. Large residual stresses develop in these layers due to thermal expansion mismatch that occurs during cool down from high temperature spraying and cyclic operating conditions. Despite their standard use, much is to be determined as to how these residual stresses are linked to the various failure modes. This study developed techniques to monitor the strain and stress in these internal layers during thermal gradient and mechanical conditions representing operating conditions. The thermal gradient is applied across the coating thickness of the tubular samples from infrared heating of the outer coating and forced air internal cooling of the substrate. While thermal and mechanical loading conditions are applied, 2-dimensional diffraction measurements are taken using the high-energy Synchrotron X-Rays and analyzed to provide high-resolution depth-resolved strain. This study will include fatigue comparisons through use of samples, which are both 'as-coated' as well as aged to various stages in a TBC lifespan. Studies reveal that variations in thermal gradients and mechanical loads create corresponding trends in depth resolved strains with the largest effects displayed at or near the bond coat/TBC interface. Single cycles as well as experiments targeting thermal gradient and mechanical effects were conducted to capture these trends. Inelastic behavior such as creep was observed and quantified for the different layers at high temperatures. From these studies more accurate lifespan predictions, material behaviors, and causes of failure modes can be determined. The work further develops measurement and analysis techniques for diffraction measurements in internal layers on a coated tubular sample which can be used by various industries to analyze similar geometries with different applications.
Show less - Date Issued
- 2014
- Identifier
- CFE0005640, ucf:50206
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0005640
- Title
- MICROSCOPIC SURFACE TEXTURES CREATED BY INTERFACIAL FLOW INSTABILITIES.
- Creator
-
Gu, Jing, Weiwei Deng, Dr., University of Central Florida
- Abstract / Description
-
In nature, microscopic surface textures impact useful function, such as the drag reduction of shark skin (Dean & Bhushan, 2010) and superhydrophobicity of the lotus leaf(Pan, Kota, Mabry, & Tuteja, 2013). In this study, we explore these phenomena by re-creating microscopic surface textures via the method of interfacial flow instability in drying polyvinylidene fluoride (PVDF) acetone solutions. In general, PVDF films can be made using either spin coating or electrospray deposition with...
Show moreIn nature, microscopic surface textures impact useful function, such as the drag reduction of shark skin (Dean & Bhushan, 2010) and superhydrophobicity of the lotus leaf(Pan, Kota, Mabry, & Tuteja, 2013). In this study, we explore these phenomena by re-creating microscopic surface textures via the method of interfacial flow instability in drying polyvinylidene fluoride (PVDF) acetone solutions. In general, PVDF films can be made using either spin coating or electrospray deposition with various weight concentrations in acetone. In order to study the morphology of the porous structure of PVDF films, wet deposition samples were fabricated by spin coating or near-field electrospray. Possible theories are discussed and examined to explain the formation of these porous structures resulting in development of a well-controlled method to create porous PVDF films with various pore sizes and pore densities. All samples are characterized and found to exhibit superhydrophobicity and drag reduction. To connect porous PVDF film morphology to the established field of dry particle fabrication, PVDF particle synthesis by far-field electrospray is also reviewed and discussed. An established method to generate polymer particles of different morphologies in other polymers (Almeria-Diez, 2012) by electrospray drying is confirmed using PVDF as well. Due to the ability of scalable and re-configurable electrospray, the microscopic surface textures can be applied to areas of any size to reduce drag or impart water-repelling properties.
Show less - Date Issued
- 2013
- Identifier
- CFH0004479, ucf:45066
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFH0004479
- Title
- STRUCTURAL CHARACTERIZATION OF SPUTTER-DEPOSITED SS304+XAL (X = 0, 4, 7 AND 10 WT.%) COATINGS AND MECHANICALLY MILLED TI, ZR AND HF POWDERS.
- Creator
-
Seelam, Uma Maheswara, Suryanarayana, Challapalli, University of Central Florida
- Abstract / Description
-
Study of the metastable phases obtained by non-equilibrium processing techniques has come a long way during the past five decades. New metastable phases have often given new perspectives to the research on synthesis of novel materials systems. Metastable materials produced by two non-equilibrium processing methods were studied for this dissertation- 304-type austenitic stainless steel (SS304 or Fe-18Cr-8Ni)+aluminum coatings produced by plasma enhanced magnetron sputter-deposition (PEMS) and...
Show moreStudy of the metastable phases obtained by non-equilibrium processing techniques has come a long way during the past five decades. New metastable phases have often given new perspectives to the research on synthesis of novel materials systems. Metastable materials produced by two non-equilibrium processing methods were studied for this dissertation- 304-type austenitic stainless steel (SS304 or Fe-18Cr-8Ni)+aluminum coatings produced by plasma enhanced magnetron sputter-deposition (PEMS) and nanocrystalline Ti, Zr and Hf powders processed by mechanical milling (MM). The objective of the study was to understand the crystallographic and microstructural aspects of these materials. Four SS304+Al coatings with a nominal Al percentages of 0, 4, 7 and 10 wt.% in the coatings were deposited on an SS304 substrate by PEMS using SS304 and Al targets. The as-deposited coatings were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and three-dimensional atom probe microscopy (3DAP). Surface morphology and chemical analysis were studied by SEM. Phase identification was carried out by XRD and TEM. The microstructural features of all the coatings, as observed in the TEM, consisted of columnar grains with the columnar grain width (a measure of grain size) increasing with an increase in the Al content. The coatings had grains with average grain sizes of about 100, 290, 320 and 980 nm, respectively for 0, 4, 7 and 10 wt.% Al. The observed grain structures and increase in grain size were related to substrate temperature during deposition. XRD results indicated that the Al-free coating consisted of the non-equilibrium ferrite and sigma phases. In the 4Al, 7Al and 10Al coatings, equilibrium ferrite and B2 phases were observed but no sigma phase was found. In 10Al coating, we were able to demonstrate experimentally using 3DAP studies that NiAl phase formation is preferred over the FeAl phase at nano scale. During mechanical milling of the hexagonal close packed (HCP) metals Hf, Ti and Zr powders, unknown nanocrystalline phases with face centered cubic (FCC) structure were found. The FCC phases could be either allotropes of the respective metals or impurity stabilized phases. However, upon MM under high purity conditions, it was revealed that the FCC phases were impurity stabilized. The decrease in crystallite size down to nanometer levels, an increase in atomic volume, lattice strain, and possible contamination were the factors responsible for the transformation.
Show less - Date Issued
- 2010
- Identifier
- CFE0003161, ucf:48595
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0003161
- Title
- A Linear Multiplexed Electrospray Thin Film Deposition System.
- Creator
-
Lojewski, Brandon, Deng, Weiwei, Chen, Ruey-Hung, Chen, Quanfang, University of Central Florida
- Abstract / Description
-
Liquid spray is essential to industries requiring processes such as spray coating, spray drying, spray pyrolysis, or spray cooling. This thesis reports the design, fabrication, and characterization of a thin film deposition system which utilizes a linear multiplexed electrospray (LINES) atomizer. First, a thorough review of the advantages and limitations of prior multiplexed electrospray systems leads to discussion of the design rationale for this work. Next, the line of charge model was...
Show moreLiquid spray is essential to industries requiring processes such as spray coating, spray drying, spray pyrolysis, or spray cooling. This thesis reports the design, fabrication, and characterization of a thin film deposition system which utilizes a linear multiplexed electrospray (LINES) atomizer. First, a thorough review of the advantages and limitations of prior multiplexed electrospray systems leads to discussion of the design rationale for this work. Next, the line of charge model was extended to prescribe the operating conditions for the experiments and to estimate the spray profile. The spray profile was then simulated using a Lagrangian model and solved using a desktop supercomputer based on Graphics Processing Units (GPUs). The simulation was extended to estimate the droplet number density flux during deposition. Pure ethanol was electrosprayed in the cone-jet mode from a 51-nozzle aluminum LINES atomizer with less than 3% relative standard deviation in the D10 average droplet diameter as characterized using Phase Doppler Interferometry (PDI). Finally a 25-nozzle LINES was integrated into a thin film deposition system with a heated, motion controlled stage, to deposit TiO2 thin films onto silicon wafers from an ethanol based nanoparticle suspension. The resulting deposition pattern was analyzed using SEM, optical profilometry, and macro photography and compared with the numerical simulation results. The LINES tool developed here is a step forward to enabling the power of electrospray for industrial manufacturing applications in clean energy, health care, and electronics.
Show less - Date Issued
- 2013
- Identifier
- CFE0005106, ucf:50745
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0005106
- Title
- Synchrotron X-Ray Diffraction and Piezospectroscopy used for the Investigation of Individual Mechanical Effects from Environmental Contaminants and Oxide Layer Undulations in Thermal Barrier Coatings.
- Creator
-
Siddiqui, Sanna, Raghavan, Seetha, Bai, Yuanli, Gordon, Ali, University of Central Florida
- Abstract / Description
-
The durability of Thermal Barrier Coatings (TBCs) used on the turbine blades of aircraft and power generation engines has been known to be affected by sand particle ingression comprised of Calcium-Magnesium-Alumina-Silicate (CMAS). Previous studies have shown that these effects present themselves through variations in the thermomechanical and thermochemical properties of the coating. This study investigated the impact of CMAS ingression on the Yttria Stabilized Zirconia Topcoat (YSZ) and...
Show moreThe durability of Thermal Barrier Coatings (TBCs) used on the turbine blades of aircraft and power generation engines has been known to be affected by sand particle ingression comprised of Calcium-Magnesium-Alumina-Silicate (CMAS). Previous studies have shown that these effects present themselves through variations in the thermomechanical and thermochemical properties of the coating. This study investigated the impact of CMAS ingression on the Yttria Stabilized Zirconia Topcoat (YSZ) and Thermally Grown Oxide (TGO) strain in sprayed Thermal Barrier Coating (TBC) samples of varying porosity with and without CMAS ingression. In-Situ Synchrotron X-ray Diffraction measurements were taken on the sample under thermal loading conditions from which the YSZ and TGO peaks were identified and biaxial strain calculations were determined at high temperature. Quantitative strain results are presented for the YSZ and TGO during a thermal cycle. In-plane strain results for YSZ near the TGO interface for a complete thermal cycle are presented, for a 6% porous superdense sample with CMAS infiltration. The outcomes from this study can be used to understand the role of CMAS on the strain tolerance of the TBC coating.It is well known that under engine operational conditions the development of the TGO layer, with large critical stresses, has been linked to failure of the coating. The growth of the TGO manifests as undulations in a series of peaks and troughs. Understanding the mechanics of the oxide layer at these locations provides significant information with respect to the failure mechanisms of the TBC coating. This study investigated the stress at the peak and trough of a TGO undulation for a cycled Dense Vertically Cracked (DVC) plasma sprayed TBC sample through photo-luminescence (PL) spectroscopy. High resolution nanoscale stress maps were taken nondestructively in the undulation of the TGO. Preliminary results from first line mapping of TGO peak and trough scan, at a resolution of 200 nm, have shown a non-uniform TGO stress variation. The results obtained from this study can be used to understand the stress variation in the peak and trough of a DVC sample's TGO undulation and how it contributes to the life of the TBC coating.
Show less - Date Issued
- 2014
- Identifier
- CFE0005712, ucf:50136
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0005712
- Title
- Assessment, Optimization, and Enhancement of Ultrafiltration (UF) Membrane Processes in Potable Water Treatment.
- Creator
-
Boyd, Christopher, Duranceau, Steven, Cooper, Charles, Randall, Andrew, University of Central Florida
- Abstract / Description
-
This dissertation reports on research related to ultrafiltration (UF) membranes in drinking water applications. A pilot-scale investigation identified seasonal surface water quality impacts on UF performance and resulted in the development of a dynamic chemically enhanced backwash protocol for fouling management. Subsequent analysis of UF process data revealed limitations with the use of specific flux, transmembrane pressure (TMP), and other normalization techniques for assessing UF process...
Show moreThis dissertation reports on research related to ultrafiltration (UF) membranes in drinking water applications. A pilot-scale investigation identified seasonal surface water quality impacts on UF performance and resulted in the development of a dynamic chemically enhanced backwash protocol for fouling management. Subsequent analysis of UF process data revealed limitations with the use of specific flux, transmembrane pressure (TMP), and other normalization techniques for assessing UF process fouling. A new TMP balance approach is presented that identifies the pressure contribution of membrane fouling and structural changes, enables direct process performance comparisons at different operating fluxes, and distinguishes between physically and chemically unresolved fouling. In addition to the TMP balance, a five component optimization approach is presented for the systematic improvement of UF processes on the basis of TMP variations. Terms are defined for assessing process event performance, a new process utilization term is presented to benchmark UF productivity, and new measures for evaluating maintenance procedures are discussed. Using these tools, a correlation between process utilization and operating pressures was established and a sustainable process utilization of 93.5% was achieved. UF process capabilities may be further enhanced by pre-coating media onto the membrane surface. Silicon dioxide (SiO2) and powdered activated carbon (PAC) are evaluated as pre-coating materials, and the applicability of the TMP balance for assessing pre-coated membrane performance is demonstrated. The first use of SiO2 as a support layer for PAC in a membrane pre-coating application is presented at the laboratory-scale. SiO2-PAC pre-coatings successfully reduced physically unresolved fouling and enhanced UF membrane organics removal capabilities.
Show less - Date Issued
- 2013
- Identifier
- CFE0005088, ucf:50758
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0005088
- Title
- NUMERICAL SIMULATION OF FRACTURE OF A NANO-PAPER COATED E-GLASS/POLYESTER COMPOSITE WITH THERMAL DAMAGE.
- Creator
-
Graham, Zachary, Gordon, Ali, University of Central Florida
- Abstract / Description
-
Aerospace research for next-generation travel increasingly focuses on the use of advanced composites to reduce weight and cost while retaining strength. One subset of materials with great potential is based on the combination of resin matrix and glass-fiber reinforcement. This research explores the application of a candidate nanopaper coating with a given composite. Prior research applied a set of given heat fluxes to the top surface of the composite for a set of given periods of time, and...
Show moreAerospace research for next-generation travel increasingly focuses on the use of advanced composites to reduce weight and cost while retaining strength. One subset of materials with great potential is based on the combination of resin matrix and glass-fiber reinforcement. This research explores the application of a candidate nanopaper coating with a given composite. Prior research applied a set of given heat fluxes to the top surface of the composite for a set of given periods of time, and subsequently performed a 3-point flexural test to determine the elastic modulus for both the coated and uncoated composite for all of the combinations of heat flux and time. A finite element (FE) model is developed using the ANSYS general purpose finite element analysis (FEA) software that models the degradation in strength/stiffness properties based on heating condition and with the goal of predicting cracking using the element death feature in ANSYS. This thesis describes the prior research suggesting both the need for and novelty of this model, and the procedures used to form the model. The loading conditions of the 3-point flexural test are replicated, and four measures of accuracy are developed based on the force versus displacement curve of the test and the FE model. It is envisioned that continuum-level models developed as a part of these research be applied for design of next-generation space components These measurements are used to verify the FE model, and this model is then employed to extrapolate beyond the context of experimental conditions.
Show less - Date Issued
- 2013
- Identifier
- CFH0004346, ucf:45021
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFH0004346
- Title
- INVESTIGATION OF PS-PVD AND EB-PVD THERMAL BARRIER COATINGS OVER LIFETIME USING SYNCHROTRON X-RAY DIFFRACTION.
- Creator
-
Northam, Matthew, Raghavan, Seetha, Ghosh, Ranajay, Vaidyanathan, Raj, University of Central Florida
- Abstract / Description
-
Extreme operating temperatures within the turbine section of jet engines require sophisticated methods of cooling and material protection. Thermal barrier coatings (TBCs) achieve this through a ceramic coating applied to a substrate material (nickel-based superalloy). Electron-beam physical vapor deposition (EB-PVD) is the industry standard coating used on jet engines. By tailoring the microstructure of an emerging deposition method, Plasma-spray physical vapor deposition (PS-PVD), similar...
Show moreExtreme operating temperatures within the turbine section of jet engines require sophisticated methods of cooling and material protection. Thermal barrier coatings (TBCs) achieve this through a ceramic coating applied to a substrate material (nickel-based superalloy). Electron-beam physical vapor deposition (EB-PVD) is the industry standard coating used on jet engines. By tailoring the microstructure of an emerging deposition method, Plasma-spray physical vapor deposition (PS-PVD), similar microstructures to that of EB-PVD coatings can be fabricated, allowing the benefits of strain tolerance to be obtained while improving coating deposition times. This work investigates the strain through depth of uncycled and cycled samples using these coating techniques with synchrotron X-ray diffraction (XRD). In the TGO, room temperature XRD measurements indicated samples of both deposition methods showed similar in-plane compressive stresses after 300 and 600 thermal cycles. In-situ XRD measurements indicated similar high-temperature in-plane and out-of-plane stress in the TGO and no spallation after 600 thermal cycles for both coatings. Tensile in-plane residual stresses were found in the YSZ uncycled PS-PVD samples, similar to APS coatings. PS-PVD samples showed in most cases, higher compressive residual in-plane stress at the YSZ/TGO interface. These results provide valuable insight for optimizing the PS-PVD processing parameters to obtain strain compliance similar to that of EB-PVD. Additionally, external cooling methods used for thermal management in jet engine turbines were investigated. In this work, an additively manufactured lattice structure providing transpiration cooling holes is designed and residual strains are measured within an AM transpiration cooling sample using XRD. Strains within the lattice structure were found to have greater variation than that of the AM solid wall. These results provide valuable insight into the viability of implementing an AM lattice structure in turbine blades for the use of transpiration cooling.
Show less - Date Issued
- 2019
- Identifier
- CFE0007844, ucf:52830
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0007844
