View All Items

Title: PROCESSING, MICROSTRUCTURAL AND MECHANICAL CHARACTERIZATION OF MECHANICALLY ALLOYED AL-ALUMINA NANOCOMPOSITES.
Creator: Katiyar, Pushkar, SURYANARAYANA, C., University of Central Florida
Abstract / Description: Aluminum-alumina nanocomposites were synthesized using mechanical alloying of blended component powders of pure constituents. This study was performed on various powder mixtures with aluminum as the matrix and alumina as the reinforcement with volume fractions of 20, 30, and 50 % and Alumina particle sizes of 50 nm, 150 nm, and 5 µm. X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques were used for the crystal structure and microstructural characterization of the...
Show moreAluminum-alumina nanocomposites were synthesized using mechanical alloying of blended component powders of pure constituents. This study was performed on various powder mixtures with aluminum as the matrix and alumina as the reinforcement with volume fractions of 20, 30, and 50 % and Alumina particle sizes of 50 nm, 150 nm, and 5 µm. X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques were used for the crystal structure and microstructural characterization of the powders at different stages of milling. Alumina powders with 50 nm and 150 nm particle size were predominantly of gamma-type, while Alumina of 5 µm size was of alpha-type. The main goal was to achieve uniform distribution of the alumina ceramic particles in the Al matrix, which was achieved on milling for 24 h in a SPEX mill or 100 h in a Fritsch Pulverisette planetary ball mill. The powders were consolidated in two stages: pre-compaction at room temperature followed by vacuum hot pressing (VHP) or hot isostatic pressing (HIP) techniques to a fully dense condition. The effect of reinforcement particle size and volume fraction on the stress-strain response, elastic modulus and yield strength of the composites was investigated. Nanoindentation and compression tests were performed to characterize the composite material. Yield strength of 515 MPa, compressive strength of 685 MPa and elastic modulus of 36 GPa were obtained from compression tests. Nanoindentation results gave the yield strength of 336 MPa, maximum shear stress of 194 MPa and an elastic modulus of 42 GPa. The low elastic modulus values obtained from the above tests might be because of localized yielding possibly due to residual stresses.
Show less
Date Issued: 2004
Identifier: CFE0000128, ucf:46193
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0000128

Title: MULTIFUNCTIONAL NANOCOMPOSITES FOR HIGH DAMPING PERFORMANCE.
Creator: Algozzini, Lee, Gou, Jan, University of Central Florida
Abstract / Description: Composite structures for aerospace and wind turbine applications are subjected to high acoustic and vibrational loading and exhibit very high amplitude displacements and thus premature failure. Materials with high damping or absorbing properties are crucially important to extend the life of structures. Traditional damping treatments are based on the combinations of viscoelastic, elastomeric, magnetic, and piezoelectric materials. In this work, the use of carbon nanofibers (CNFs) in the form...
Show moreComposite structures for aerospace and wind turbine applications are subjected to high acoustic and vibrational loading and exhibit very high amplitude displacements and thus premature failure. Materials with high damping or absorbing properties are crucially important to extend the life of structures. Traditional damping treatments are based on the combinations of viscoelastic, elastomeric, magnetic, and piezoelectric materials. In this work, the use of carbon nanofibers (CNFs) in the form of interconnected self-supportive paper as reinforcement can significantly improve damping performance. The interfacial friction is the primary source of energy dissipation in CNF paper based nanocomposites. The approach entailed making CNF paper by filtration of well-dispersed nanofibers under controlled processing conditions. The CNF paper was integrated into composite laminates using modified liquid composite molding processes including Resin Transfer Molding (RTM) and Vacuum Assisted Resin Transfer Molding (VARTM). The rheological and curing behaviors of the CNF-modified polymer resin were characterized with Viscometry and Differential Scanning Calorimetry (DSC). The process analysis in mold filling and pressure distribution was conducted using Control Volume Finite Element Method (CVFEM) in an attempt to optimize the quality of multifunctional nanocomposites. The mold filling simulation was validated with flow visualization in a transparent mold. Several tests were performed to study the damping properties of the fabricated composites including Dynamic Mechanical Analysis (DMA) and piezoceramic patch based vibration tests. It was found that the damping performance was significantly enhanced with the incorporation of carbon nanofibers into the composite structures.
Show less
Date Issued: 2009
Identifier: CFE0002839, ucf:48078
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0002839

Title: CALIBRATION OF ALUMINA-EPOXY NANOCOMPOSITES USING PIEZOSPECTROSCOPY FOR THE DEVELOPMENT OF STRESS-SENSING ADHESIVES.
Creator: Stevenson, Amanda, Raghavan, Seetha, University of Central Florida
Abstract / Description: A non-invasive method to quantify the stress distribution in polymer-based materials is presented through the piezospectroscopic calibration of alumina-epoxy nanocomposites. Three different alumina volume fraction nanocomposites were created and loaded under uniaxial compression in order to determine the relationship between applied stress and the frequency shift of the R-lines produced by alumina under excitation. Quantitative values for six piezospectroscopic coefficients were obtained...
Show moreA non-invasive method to quantify the stress distribution in polymer-based materials is presented through the piezospectroscopic calibration of alumina-epoxy nanocomposites. Three different alumina volume fraction nanocomposites were created and loaded under uniaxial compression in order to determine the relationship between applied stress and the frequency shift of the R-lines produced by alumina under excitation. Quantitative values for six piezospectroscopic coefficients were obtained which represent the stress-sensing property of the nanocomposites. The results were applied to an alumina-filled adhesive in a single lap shear configuration demonstrating the capability of the technique to monitor R-line peak positions with high spatial resolution and assess the stress distribution within the material prior to failure. Additionally, particle dispersion and volume fraction were confirmed with spectral intensities, introducing a novel experimental method for the assessment of quality in manufacturing of such nanocomposites. Results were further used to initiate studies in determining the load transfer to the nanoparticles and assessing the fundamental driving mechanisms.
Show less
Date Issued: 2011
Identifier: CFE0003744, ucf:48777
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003744

Title: Piezospectroscopic Calibration of Alumina-Nanocomposites for the Development of Stress-Sensing Structures.
Creator: Fugon-Dessources, Daniela, Raghavan, Seetha, Gou, Jihua, Orlovskaya, Nina, University of Central Florida
Abstract / Description: Alpha-alumina is known to exhibit photo-luminescent (PL) properties, mainly characteristic R-lines that shift according to applied stress. In addition to showing excellent PL properties, polymers with embedded alumina nanoparticles have been shown to improve the overall composite mechanical properties. While the use of the PL properties to develop stress-sensing materials using an alumina-epoxy material has been success- fully shown in compression, the properties have not been developed for...
Show moreAlpha-alumina is known to exhibit photo-luminescent (PL) properties, mainly characteristic R-lines that shift according to applied stress. In addition to showing excellent PL properties, polymers with embedded alumina nanoparticles have been shown to improve the overall composite mechanical properties. While the use of the PL properties to develop stress-sensing materials using an alumina-epoxy material has been success- fully shown in compression, the properties have not been developed for tension. In this study, the PL response of variable volume fraction alumina-epoxy composites will be determined under tensile conditions. It is expected that increasing the volume fraction of alumina nanoparticles will increase the sensitivity of the particles PL emission shift to applied stress. Three tensile alumina-epoxy specimens of 21.0%, 31.2%, and 34.5% volume fractions were manufactured and tested under tensile static loads. The results of this experiment will determine the piezospectroscopic (PS) coefficient and calibration of bulk alumina nanocomposites in tension. A linear region was identified in the PS response of the nanocomposite to the applied tensile load. The PS coefficient of this linear region increased as the volume fraction of the nanocomposite increased. To demonstrate the application of structural composites with stress sensing capabilities, alumina nanoparticles were integrated in the manufacturing of a carbon fiber composite specimen. The results of the stress-sensing composite mechanical experiment showed that alumina nanoparticles were able to detect changes in stress. The results for both the bulk nanocomposite calibrations and the application of stress-sensing alumina nanoparticles in a carbon-fiber composite will advance the development of this novel stress-sensing method.
Show less
Date Issued: 2014
Identifier: CFE0005168, ucf:50661
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0005168

Title: PLASMA PROCESSING FOR RETENTION OF NANOSTRUCTURES.
Creator: Venkatachalapathy, Viswanathan, Seal, Sudipta, University of Central Florida
Abstract / Description: Plasma spray processing is a technique that is used extensively in thermal barrier coatings on gas and steam turbine components, biomedical implants and automotive components. Many processing parameters are involved to achieve a coating with certain functionality. The coating could be required to function as thermal barrier, wear resistant, corrosion resistant or a high temperature oxidation resistant coating. Various parameters, such as, nozzle and electrode design, powder feeding system,...
Show morePlasma spray processing is a technique that is used extensively in thermal barrier coatings on gas and steam turbine components, biomedical implants and automotive components. Many processing parameters are involved to achieve a coating with certain functionality. The coating could be required to function as thermal barrier, wear resistant, corrosion resistant or a high temperature oxidation resistant coating. Various parameters, such as, nozzle and electrode design, powder feeding system, spray distances, substrate temperature and roughness, plasma gas flow rates and others can greatly alter the coating quality and resulting performance. Feedstock (powder or solution precursor) composition and morphology are some of the important variables, which can affect the high end coating applications. The amount of heat a plasma plume has to offer to the particles being processed as a coating depends primarily on the dissociation of the atoms of gaseous mixtures being used to create the plasma and the residence time required for the particle to stay in the flame. The parameters that are conducive for nanostructured retention could be found out if the residence time of the particles in the flame and the available heat in the plume for various gas combinations could be predicted. If the feedstock is a liquid precursor instead of a powder feedstock, the heat that has to be offered by the plasma could be increased by suitable gas combination to achieve a good quality coating. Very little information is available with regard to the selection of process parameters and processing of nano materials feedstock to develop nanostructured coatings using plasma spray. In this study, it has been demonstrated that nano ceramics or ceramic composites either in the form of coatings or bulk free form near net components could be processed using DC plasma spray. For powder feedstock, analytical heat transfer calculations could predict the particle states for a given set of parameters by way of heat input from the plasma to the particles. The parameter selection is rendered easier by means of such calculations. Alumina nano ceramic particles are processed as a coating. During Spray drying, a process of consolidation of nano alumina particles to spherical agglomerates, parameter optimization for complete removal of moisture has been achieved. The parameters are tested for alumina nanoparticles with a plasma torch for the veracity of calculations. The amount of heat transfer from the surface of the agglomerates to the core has been quantified as a function of velocity of particles. Since preparation of nanostructured feedstock for plasma spray is expensive and cumbersome, alternative solution precursor route for direct pyrolysis of precursor to coating has been studied in case of nanocrystalline rare earth oxides. Thus, it has also been shown by this research that nanostructured coatings could be either from a powder feedstock or a solution precursor feedstock. MoSi2-Si3N4, Ni-Al2O3, W-HfC nano ceramic composite systems have been processed as a bulk free form nanocomposite with 60-70% retained nanostructures. The importance of selection of substrates, roughness and the substrate temperature for development of free form bulk components has been highlighted. The improvement in mechanical and high temperature properties associated with having such nanostructured coatings or bulk nanocomposites are revealed. These nanostructured coatings are known for their low thermal conductivity, high wear resistance and can be potentially used as steam and gas turbines coatings for improved thermal efficiency. In summary, bulk nanocomposite through plasma spray processing is a viable alternative to conventional processes such as sintering, HIP for high fracture toughness and hardness applications.
Show less
Date Issued: 2007
Identifier: CFE0001680, ucf:47203
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0001680

Title: Synthesis and Properties of Self-Assembled C/SiCN Nanocomposite Derived from Polymer Precursors.
Creator: Li, Cheng, An, Linan, Fang, Jiyu, Coffey, Kevin, Liao, Yi, Xu, Chengying, Zhai, Lei, University of Central Florida
Abstract / Description: The properties of C/SiCN nanocomposites synthesized by thermal decomposition of polymer precursors were studied in this work. The novel polymer-to-ceramic process enables us to tailor the ceramic structure in atomic level by designing the starting chemicals and pyrolysis procedures. It is of both fundamental and practical significance to investigate the properties and structures relationship of the nanocomposites. In this work, we explored their application potential in using as anode of...
Show moreThe properties of C/SiCN nanocomposites synthesized by thermal decomposition of polymer precursors were studied in this work. The novel polymer-to-ceramic process enables us to tailor the ceramic structure in atomic level by designing the starting chemicals and pyrolysis procedures. It is of both fundamental and practical significance to investigate the properties and structures relationship of the nanocomposites. In this work, we explored their application potential in using as anode of lithium-ion secondary batteries. The structure and structural evolution of C/SiCN nanocomposite were investigated by using XRD, FTIR, SEM, TEM, Solid state NMR and Raman spectroscopy. The results revealed the nanocomposites consisted of amorphous SiCxNx-4 matrix and carbon nanoclusters distributed within it. The size of the carbon was measured by Raman spectroscopy, varied with starting chemicals and pyrolysis temperature. The electronic properties of the C/SiCN nanocomposite were studied by measuring the I-V curves and a.c. impedance. The d.c. conductivity increased with carbon content and pyrolysis temperatures. The impedance spectra and fitted equivalent circuit results confirmed the existence of two phases in the nanocomposite. The possibility of using C/SiCN as anode in lithium-ion secondary batteries was investigated by electrochemical measurements, namely cyclic voltammetry, galvanostatic cyclic test and electrochemical impedance spectroscopy. The galvanostatic measurements showed that the nanocomposite with 26% of carbon nanoclusters exhibited a specific capacity of 480 mAh/g, which is 30% higher than that of commercial graphite anode. The high capacity of the nanocomposites is attributed to the formation of a novel structure around C/SiCN interface. The excellent electrochemical properties, together with the simple, low-cost processing, make the nanocomposites very promising for Li-ion battery applications.
Show less
Date Issued: 2012
Identifier: CFE0004194, ucf:49028
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004194

Title: High Volume Fraction Mg-based Nanocomposites: Processing, Microstructure and Mechanical Behavior.
Creator: Liu, Jinling, An, Linan, Suryanarayana, Challapalli, Fang, Jiyu, Bai, Yuanli, Lin, Kuo-Chi, University of Central Florida
Abstract / Description: Mg-based metal matrix nanocomposites (MMNCs) with mechanical properties, superior to those of coarse-grained composites, are promising structural materials for applications in the automotive and aerospace industries. The research in this area was primarily focused earlier on either micro-scaled reinforcements or nano-scaled reinforcements with very low volume fractions. MMNCs with high volume fractions have not been explored yet. In this research, we study the processing, microstructures and...
Show moreMg-based metal matrix nanocomposites (MMNCs) with mechanical properties, superior to those of coarse-grained composites, are promising structural materials for applications in the automotive and aerospace industries. The research in this area was primarily focused earlier on either micro-scaled reinforcements or nano-scaled reinforcements with very low volume fractions. MMNCs with high volume fractions have not been explored yet. In this research, we study the processing, microstructures and properties of MMNCs containing ceramic nanoparticles up to 30 vol.%.We first investigated the mechanical alloying of Al2O3 nanoparticles and pure Mg under high-energy ball milling conditions. The phase evolution and their distribution were evaluated as a function of milling time. Then, the thermal stability of the formed nanocomposites was investigated by annealing it at high temperatures. It indicated that an exchange reaction had occurred to a large extent between Mg and Al2O3 resulting in the formation of Al and MgO phases. Additionally, the reaction between Al and un-reacted Mg led to the formation of Mg-Al intermetallics.Due to the reaction between Mg and Al2O3 during the milling and annealing process, we attempted to synthesize Mg/SiC nanocomposites. The mixed powders containing 0, 5, 10 and 15 vol.% SiC were produced by high energy ball milling and then the powders were consolidated via spark plasma sintering. The phase constitutions and microstructures of the Mg/SiC nanocomposites were characterized. SiC nanoparticles (average particle size ~14 nm) appear to be homogeneously dispersed within the matrix, and the average inter-particle spacings of all the Mg/SiC nanocomposites were smaller than 50 nm. Microscopic methods, even at high magnifications did not reveal any significant porosity in the as-processed MMNCs.Mechanical characterization of the Mg/SiC nanocomposites was conducted using the microindentation test. Besides the microhardness test, different intermediate pause times and loading rates were used to evaluate the stiffness and loading rate sensitivity of our samples. The abnormal microhardness and loading rate sensitivity were showed for the Mg-15 vol.% SiC samples. At the same time, the monotonic increase of stiffness with volume fraction was exhibited in the Mg/SiC nanocomposites.Finally, we investigated the quasi-static and dynamic response of Mg/SiC nanocomposites and microcomposites, and discussed the underlying mechanisms. Strain softening was noticed in the milled Mg sample under quasi-static compression. Similarly, the strengthening effect leveling off was also observed in the Mg-15 vol.% SiC samples under either quasi-static or high-strain rate uniaxial compression conditions. No significant plastic deformation was observed in the Mg/SiC nanocomposites. The estimated strain rate sensitivity of all the Mg/SiC nanocomposites in this work was around 0.03, which is much smaller than 0.3 and 0.6, observed for 100 nm and 45 nm grain size pure Mg individually. In particular, the existing models fail in predicting the inverse volume fraction effect, and other mechanisms are yet to be explored. The presence of SiC nanoparticles may play an important role that leads to this difference.
Show less
Date Issued: 2013
Identifier: CFE0004879, ucf:49672
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004879

Title: PERCOLATION STUDY OF NANO-COMPOSITE CONDUCTIVITY USING MONTE CARLO SIMULATIONPERCOLATION.
Creator: Bai, Jing, Lin, Kuo-Chi, University of Central Florida
Abstract / Description: A Monte Carlo model is developed for predicting electrical conductivity of carbon nanofiber composite materials. The conductive nanofibers are models as both 2D and 3D network of finite sites that are randomly distributed. The percolation behavior of the network is studied using the Monte Carlo method, which leads to the determination of the percolation threshold. The effect of the nanofiber aspect ratio on the critical nanofiber volume rate is investigated in the current model, each of the...
Show moreA Monte Carlo model is developed for predicting electrical conductivity of carbon nanofiber composite materials. The conductive nanofibers are models as both 2D and 3D network of finite sites that are randomly distributed. The percolation behavior of the network is studied using the Monte Carlo method, which leads to the determination of the percolation threshold. The effect of the nanofiber aspect ratio on the critical nanofiber volume rate is investigated in the current model, each of the nanofibers needs five independent geometrical parameters (i.e., three coordinates in space and two orientation angles) for its identification. There are three controlling parameters for each nanofiber, which includes the nanofiber length, the nanofiber diameter, and the nanofiber aspect ratio. The simulation results reveal a relationship between the fiber aspect ratio and the percolation threshold: the higher the aspect ratio, the lower the threshold. With the simulation results obtained from the Monte Carlo model, the effective electrical conductivity of the composite is then determined by assuming the conductivity is proportional to the ratio of the number of nanofibers forming the largest cluster to the total number of nanofibers. The numerical results indicate that as the volume rate reaches a critical value, the conductivity starts to rise sharply. These obtained simulation results agree fairly with experimental and numerical data published earlier by others. In addition, we investigate the convergence of the current percolation model. We also find the tunneling effect does not affect the critical volume rate greatly. We propose that the percolation model is not scalable as well.
Show less
Date Issued: 2009
Identifier: CFE0002644, ucf:48230
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0002644

Title: MECHANICAL PROPERTIES OF CARBON NANOTUBE / METAL COMPOSITES.
Creator: Sun, Ying, Chen, Quanfang, University of Central Florida
Abstract / Description: Carbon nanotubes (CNTs) have captured a great deal of attention worldwide since their discovery in 1991. CNTs are considered to be the stiffest and strongest material due to their perfect atomic arrangement and intrinsic strong in-plane sp2Ã‚Â--sp2 covalent bonds between carbon atoms. In addition to mechanical properties, CNTs have also shown exceptional chemical, electrical and thermal properties. All these aspects make CNTs promising candidates in the development of novel...
Show moreCarbon nanotubes (CNTs) have captured a great deal of attention worldwide since their discovery in 1991. CNTs are considered to be the stiffest and strongest material due to their perfect atomic arrangement and intrinsic strong in-plane sp2Ã‚Â--sp2 covalent bonds between carbon atoms. In addition to mechanical properties, CNTs have also shown exceptional chemical, electrical and thermal properties. All these aspects make CNTs promising candidates in the development of novel multi-functional nanocomposites. Utilizing CNTs as fillers to develop advanced nanocomposites still remains a challenge, due to the lack of fundamental understanding of both material processing at the nanometer scale and the resultant material properties. In this work, a new model was developed to investigate the amount of control specific parameters have on the mechanical properties of CNT composites. The new theory can be used to guide the development of advanced composites using carbon nanotubes, as well as other nano-fibers, with any matrices (ceramic, metal, or polymer). Our study has shown that the varying effect based on changes in CNT dimensions and concentration fit the model predictions very well. Metallic CNT composites using both single-walled carbon nanotubes (SWNT) and multi-walled carbon nanotubes (MWNT), have been developed through a novel electrochemical co-deposition process. Copper and nickel matrix composites were developed by using pulse-reverse electrochemical co-deposition. Uniaxial tensile test results showed that a more than 300% increase in strength compared to that of the pure metal had been achieved. For example, the ultimate tensile strength of Ni/CNTs composites reached as high as about 2GPa. These are best experimental results ever reported within this field. The mechanical results are mainly attributed to the good interfacial bonding between the CNTs and the metal matrices and good dispersion of carbon nanotubes within the matrices. Experimental results have also shown that the strength is inversely dependent on the diameter of carbon nanotubes. In addition to the mechanical strength, carbon nanotube reinforced metallic composites are excellent multifunctional materials in terms of electrical and thermal conduction. The electrical resistivity of carbon nanotube/copper composites produces electrical resistivity of about 1.0~1.2 x10-6ohm-cm, which is about 40% less than the pure copper. The reduced electrical resistivity is also attributed to the good interfacial bonding between carbon nanotubes and metal matrices, realized by the electrochemical co-deposition.
Show less
Date Issued: 2010
Identifier: CFE0003144, ucf:48652
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003144

Title: Synthesis, Processing and Characterization of Polymer Derived Ceramic Nanocomposite Coating Reinforced with Carbon Nanotube Preforms.
Creator: Yang, Hongjiang, Gou, Jihua, Xu, Yunjun, Lin, Kuo-Chi, University of Central Florida
Abstract / Description: Ceramics have a number of applications as coating material due to their high hardness, wear and corrosion resistance, and the ability to withstand high temperatures. Critical to the success of these materials is the effective heat transfer through a material to allow for heat diffusion or effective cooling, which is often limited by the low thermal conductivity of many ceramic materials. To meet the challenge of improving the thermal conductivity of ceramics without lowering their performance...
Show moreCeramics have a number of applications as coating material due to their high hardness, wear and corrosion resistance, and the ability to withstand high temperatures. Critical to the success of these materials is the effective heat transfer through a material to allow for heat diffusion or effective cooling, which is often limited by the low thermal conductivity of many ceramic materials. To meet the challenge of improving the thermal conductivity of ceramics without lowering their performance envelope, carbon nanotubes were selected to improve the mechanical properties and thermal dispersion ability due to its excellent mechanical properties and high thermal conductivity in axial direction. However, the enhancements are far lower than expectation resulting from limited carbon nanotube content in ceramic matrix composites and the lack of alignment. These problems can be overcome if ceramic coatings are reinforced by carbon nanotubes with good dispersion and alignment. In this study, the well-dispersed and aligned carbon nanotubes preforms were achieved in the form of vertically aligned carbon nanotubes (VACNTs) and Buckypaper. Polymer derived ceramic (PDC) was selected as the matrix to fabricate carbon nanotube reinforced ceramic nanocomposites through resin curing and pyrolysis. The SEM images indicates the alignment of carbon nanotubes in the PDC nanocomposites. The mechanical and thermal properties of the PDC nanocomposites were characterized through Vickers hardness measurement and Thermogravimetric Analysis. The ideal anisotropic properties of nanocomposites were confirmed by estimating the electrical conductivity in two orthogonal directions.
Show less
Date Issued: 2014
Identifier: CFE0005446, ucf:50385
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0005446

Title: PROCESSING AND CHARACTERIZATION OF MULTIFUNCTIONAL THERMOPLASTIC NANOCOMPOSITE FILMS.
Creator: Wang, Xin, Gou, Jihua, Challapalli, Suryanarayana, Xu, Yunjun, University of Central Florida
Abstract / Description: Nanoparticles reinforced polymer composite films have been widely studied for their enhanced mechanical, electrical and thermal properties compared with host polymer matrix. However, most research was conducted on incorporation of nanoparticles in polymer films to improve single property and there is a lack of research on the multifunctional polymer nanocomposite films. In this work, a scalable and continuous spray deposition process was developed for the production of nanoparticles...
Show moreNanoparticles reinforced polymer composite films have been widely studied for their enhanced mechanical, electrical and thermal properties compared with host polymer matrix. However, most research was conducted on incorporation of nanoparticles in polymer films to improve single property and there is a lack of research on the multifunctional polymer nanocomposite films. In this work, a scalable and continuous spray deposition process was developed for the production of nanoparticles reinforced multifunctional thermoplastic nanocomposite films. This process is capable of making a thin sheet of thermoplastic nanocomposites with high nanoparticle loadings. The smallest thickness can be 40um.The objective of this study is to design and optimize the thermoplastic nanocomposite films by utilizing nanoclay and helical carbon nanotube for multifunctional application: a) high electrical conductivity and thermal stability. Helical carbon nanotube paper based thermoplastic polyurethane nanocomposite films have been studied. The electrical conductivity and thermal stability of nanocomposite films increase a lot due to the incorporation of helical carbon nanotube paper with high electrical and thermal conductivity. The peculiar helical configuration of carbon nanotubes could greatly improve the interfacial bonding between carbon nanotubes and polymer matrix. b)High wear resistance and thermal stability. A nanoclay reinforced thermoplastic polyurethane nanocomposite coating was applied on the surface of leather. Due to the high hardness and thermal stability of nanoclay, the leather coated with nanocomposite film showed an improvement of wear resistance and thermal stability.
Show less
Date Issued: 2014
Identifier: CFE0005734, ucf:50105
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0005734

Title: PROCESSING AND STUDY OF CARBON NANOTUBE / POLYMER NANOCOMPOSITES AND POLYMER ELECTROLYTE MATERIALS.
Creator: Harish, Muthuraman, Huo, Qun, University of Central Florida
Abstract / Description: The first part of the study deals with the preparation of carbon nanotube/polymer nanocomposite materials. The dispersion of multi-walled carbon nanotubes (MWNTs) using trifluoroacetic acid (TFA) as a co-solvent and its subsequent use in polymer nanocomposite fabrication is reported. The use of carbon nanotube/ polymer nanocomposite system for the fabrication of organic solar cells is also studied. TFA is a strong but volatile acid which is miscible with many commonly used organic solvents....
Show moreThe first part of the study deals with the preparation of carbon nanotube/polymer nanocomposite materials. The dispersion of multi-walled carbon nanotubes (MWNTs) using trifluoroacetic acid (TFA) as a co-solvent and its subsequent use in polymer nanocomposite fabrication is reported. The use of carbon nanotube/ polymer nanocomposite system for the fabrication of organic solar cells is also studied. TFA is a strong but volatile acid which is miscible with many commonly used organic solvents. Our study demonstrates that MWNTs can be effectively purified and readily dispersed in a range of organic solvents including dimethyl formamide (DMF), tetrahydrofuran (THF), and dichloromethane when mixed with 10 vol% trifluoroacetic acid (TFA). X-ray photoelectron spectroscopic analysis revealed that the chemical structure of the TFA-treated MWNTs remained intact without oxidation. The dispersed carbon nanotubes in TFA/THF solution were mixed with poly(methyl methacrylate) (PMMA) to fabricate polymer nanocomposites. A good dispersion of nanotubes in solution and in polymer matrices was observed and confirmed by SEM and optical microscopy study. Low percolation thresholds of electrical conductivity were observed from the fabricated MWNT/PMMA composite films. A carbon nanotube/ polymer nanocomposites system was also used for the fabrication of organic solar cells. A blend of single-wall carbon nanotubes (SWNTs) and poly3-hexylthiophene (P3HT) was used as the active layer in the device. The device characteristics showed that the fabrication of the solar cells was successful without any shorts in the circuit. The second part of the study deals with the preparation and characterization of electrode and electrolyte materials for lithium ion batteries. A system of lithium trifluoroacetate/ PMMA was used for its study as the electrolyte in lithium battery. A variety of different processing conditions were used to prepare the polymer electrolyte system. The conductivity of the electrolyte plays a critical role in the high power output of a battery. A high power output requires fast transport of lithium ions for which the conductivity of the electrolyte must be at least 3 x 10^-4 S/cm. Electrochemical Impedance Spectroscopy (EIS) was used to determine the conductivity of the polymer electrolyte films. Among the different processing conditions used to prepare the polymer electrolyte material, wet films of PMMA/salt system prepared by using 10vol% of TFA in THF showed the best results. At about 70wt% loading of the salt in the polymer, the conductivity obtained was about 1.1 x 10^-2 S/cm. Recently, the use of vanadium oxide material as intercalation host for lithium has gained widespread attention. Sol-gel derived vanadium oxide films were prepared and its use as a cathode material for lithium ion battery was studied. The application of carbon nanotubes in lithium ion battery was explored. A carbon nanotube /block copolymer (P3HT-b-PS) composite was prepared and its potential as an anode material was evaluated.
Show less
Date Issued: 2007
Identifier: CFE0001941, ucf:47436
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0001941

Title: ALUMINA-ALUMINUM TITANATE-TITANIA NANOCOMPOSITE: SYNTHESIS, SINTERING STUDIES, ASSESSMENT OF BIOACTIVITY AND ITS MECHANICAL AND ELECTRICAL PROPERTIES.
Creator: Somani, Vikas, Kalita, Samar, University of Central Florida
Abstract / Description: This thesis reports the development, synthesis and characterization of a ceramic-ceramic nanocomposite system for its possible application as structural and electronic biomaterial in the biomedical industry. The study selected and synthesized alumina-aluminum titanate-titania (Al2O3-Al2TiO5-TiO2) nanoceramic composite using a simple Sol-Gel technique, which can be easily reproduced. Aluminum propoxide and titanium propoxide were used as precursor chemicals. Propanol and 2- methoxy ethanol...
Show moreThis thesis reports the development, synthesis and characterization of a ceramic-ceramic nanocomposite system for its possible application as structural and electronic biomaterial in the biomedical industry. The study selected and synthesized alumina-aluminum titanate-titania (Al2O3-Al2TiO5-TiO2) nanoceramic composite using a simple Sol-Gel technique, which can be easily reproduced. Aluminum propoxide and titanium propoxide were used as precursor chemicals. Propanol and 2- methoxy ethanol were used as solvent and stabilizer, respectively. Thermal analyses were performed for a systematic understanding of phase evolution from the synthesized gel. X-Ray diffraction technique was used to confirm the phase evolution, phase purity, crystallite size and crystal structure(s) of the phase(s). Calcination of the powder at low temperatures (700°C) leads to formation of Al2O3-TiO2 nanocomposite and at higher temperatures into Al2O3-Al2TiO5-TiO2 nanocomposite confirmed by XRD analysis. Electron microscopic techniques were used to investigate powder morphology, crystallite size and inter-planner spacing. High Resolution Transmission Electron Microscopy images of the calcined powder showed agglomerates of powder particles with particle size in 15-20 nm range. As-synthesized powder was uniaxially pressed into cylindrical pellets and sintered at elevated temperatures (1000-1400oC) to study the sintering behavior, densification characteristics, and measurement of mechanical and electrical properties and assessment of bioactivity. Phase transformation induced by the sintering process was analyzed by X-ray powder diffraction technique. The effects of nanosize of powder particles and multi-phases on densification, and mechanical and electrical properties were investigated. Vickers hardness and biaxial flexural strength tests were used to determine mechanical properties. Bioactivity of the nanocomposite was assessed in Simulated Body Fluid (SBF), which has the same ionic concentration as that of human plasma. Effects of biodegradation and change in mechanical properties of the composite when kept in SBF and maintained in a static condition were studied in terms of weight loss, change in the pH of the acellular solution and change in mechanical properties (hardness and biaxial strength). Scanning Electron Microscopy was used to observe the formation of apatite crystals on the surface of the nanocomposite specimens soaked in SBF. The results obtained throw light on biocompatibility and bioactivity of Al2TiO5 phase, which has not been reported so far in the literature to the best of our knowledge. Dielectric constant and dissipation factor of the sintered nanocomposite pellets were measured using HP 4284A impedance-capacitance-resistance meter and 16451 B dielectric test fixture at 1 MHz frequency. The effects of sintering time, temperature and phases present on the electrical properties were studied and are reported in the thesis.
Show less
Date Issued: 2006
Identifier: CFE0001092, ucf:46775
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0001092

Title: Processing, Characterization and Performance of Carbon Nanopaper Based Multifunctional Nanocomposites.
Creator: Liang, Fei, Gou, Jihua, Su, Ming, Fang, Jiyu, Orlovskaya, Nina, Xu, Yunjun, University of Central Florida
Abstract / Description: Carbon nanofibers (CNFs) used as nano-scale reinforcement have been extensively studied since they are capable of improving the physical and mechanical properties of conventional fiber reinforced polymer composites. However, the properties of CNFs are far away from being fully utilized in the composites due to processing challenges including the dispersion of CNFs and the viscosity increase of polymer matrix. To overcome these issues, a unique approach was developed by making carbon nanopaper...
Show moreCarbon nanofibers (CNFs) used as nano-scale reinforcement have been extensively studied since they are capable of improving the physical and mechanical properties of conventional fiber reinforced polymer composites. However, the properties of CNFs are far away from being fully utilized in the composites due to processing challenges including the dispersion of CNFs and the viscosity increase of polymer matrix. To overcome these issues, a unique approach was developed by making carbon nanopaper sheet through the filtration of well-dispersed carbon nanofibers under controlled processing conditions, and integrating carbon nanopaper sheets into composite laminates using autoclave process and resin transfer molding (RTM). This research aims to fundamentally study the processing-structure-property-performance relationship of carbon nanopaper-based nanocomposites multifunctional applications: a) Vibrational damping. Carbon nanofibers with extremely high aspect ratios and low density present an ideal candidate as vibrational damping material; specifically, the large specific area and aspect ratio of carbon nanofibers promote significant interfacial friction between carbon nanofiber and polymer matrix, causing higher energy dissipation in the matrix. Polymer composites with the reinforcement of carbon nanofibers in the form of a paper sheet have shown significant vibration damping improvement with a damping ratio increase of 300% in the nanocomposites. b) Wear resistance. In response to the observed increase in toughness of the nanocomposites, tribological properties of the nanocomposite coated with carbon nanofiber/ceramic particles hybrid paper have been studied. Due to high strength and toughness, carbon nanofibers can act as microcrack reducer; additionally, the composites coated with such hybrid nanopaper of carbon nanofiber and ceramic particles shown an improvement of reducing coefficient of friction (COF) and wear rate. c) High electrical conductivity. A highly conductive coating material was developed and applied on the surface of the composites for the electromagnetic interference shielding and lightning strike protection. To increase the conductivity of the carbon nanofiber paper, carbon nanofibers were modified with nickel nanostrands. d) Electrical actuation of SMP composites. Compared with other methods of SMP actuation, the use of electricity to induce the shape-memory effect of SMP is desirable due to the controllability and effectiveness. The electrical conductivity of carbon fiber reinforced SMP composites can be significantly improved by incorporating CNFs and CNF paper into them. A vision-based system was designed to control the deflection angle of SMP composites to desired values. The funding support from National Science Foundation and FAA Center of Excellence for Commercial Space Transportation (FAA COE CST) is acknowledged.
Show less
Date Issued: 2012
Identifier: CFE0004569, ucf:49194
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0004569

Title: UV-LIGA COMPATIBLE ELECTROFORMED NANO-STRUCTURED MATERIALS FOR MICRO MECHANICAL SYSTEMS.
Creator: LI, BO, Chen, Quanfang, University of Central Florida
Abstract / Description: UV-LIGA is a microfabrication process realzed by material deposition through microfabricated molds. UV photolithography is conducted to pattern precise thick micro molds using UV light sensitive materials, mostly SU-8, and electroforming is performed to fabricate micro metallic structures defined by the micro molds. Therefore, UV-LIGA is a bottom-up in situ material-addition process. UV-LIGA has received broad attention recently than LIGA a micro molding fabrication process using X-ray to...
Show moreUV-LIGA is a microfabrication process realzed by material deposition through microfabricated molds. UV photolithography is conducted to pattern precise thick micro molds using UV light sensitive materials, mostly SU-8, and electroforming is performed to fabricate micro metallic structures defined by the micro molds. Therefore, UV-LIGA is a bottom-up in situ material-addition process. UV-LIGA has received broad attention recently than LIGA – a micro molding fabrication process using X-ray to pattern the micro molds. LIGA is an expansive and is limited in access. In comparing to LIGA, the UV-LIGA is a cost effective process, and is widely accessible and safe. Therefore, it has been extensively used for the fabrication of metallic micro-electro-mechanical-systems (MEMS). The motivation of this research was to study micro mechanical systems fabricated with nano-structured metallic materials via UV-LIGA process. Various micro mechanical systems with high-aspect-ratio and thick metallic structures have been developed and are presented in this desertation. A novel micro mechanical valve has been developed with nano-structured nickel realized with UV-LIGA fabrication technique. Robust compact valves are crucial for space applications where payload and rubstaness are critically concerned. Two types of large flow rate robust passive micro check valve arrays have been designed, fabricated and tested for robust hydraulic actuators. The first such micro valve developed employs nanostructured nickel as the valve flap and single-crystal silicon as the substrates to house inlet and outlet channels. The Nano-structured nickel valve flap was fabricated using the UV-LIGA process developed and the microchannels were fabricated by deep reactive etching (DRIE) method. The valves were designed to operate under a high pressure (>10MPa), able to operate at high frequencies (>10kHz) in cooperating with the PZT actuator to produce large flow rates (>10 cc/s). The fabricated microvalves weigh 0.2 gram, after packing with a novel designated valve stopper. The tested results showed that the micro valve was able to operate at up to 14kHz. This is a great difference in comparison to traditional mechanical valves whose operations are limited to 500 Hz or less. The advantages of micro machined valves attribute to the scaling laws. The second type of micro mechanical valves developed is a in situ assembled solid metallic (nickel) valves. Both the valve substrates for inlet and outlet channels and the valve flap, as well as the valve stopper were made by nickel through a UV-LIGA fabrication process developed. Continuous multiple micro molds fabrication and molding processes were performed. Final micro mechanical valves were received after removing the micro molds used to define the strutures. There is no any additional machining process, such as cutting or packaging. The alignment for laminated fabrication was realized under microscope, therefore it is a highly precise in situ fabrication process. Testing results show the valve has a forward flow rate of19 cc/s under a pressure difference of 90 psi. The backward flow rate of 0.023 cc/s, which is negligible (0.13%). Nano-structured nickel has also been used to develop laminated (sandwiched) micro cryogenic heater exchanger with the UV-LIGA process. Even though nickel is apparently not a good thermal conductor at room temperature, it is a good conductor at cryogentic temerpature since its thermal conductivity increases to 1250 W/k·m at 77K. Micro patterned SU-8 molds and electroformed nickel have been developed to realize the sandwiched heat exchanger. The SU-8 mold (200mm x 200mm x50mm) array was successfully removed after completing the nickel electroforming. The second layer of patterned SU-8 layer (200mm x 200mm x50mm, as a thermal insulating layer) was patterned and aligned on the top of the electroformed nickel structure to form the laminated (sandwiched) micro heat exchanger. The fabricated sandwiched structure can withstand cryogenic temperature (77K) without any damages (cracks or delaminations). A study on nanocomposite for micro mechanical systems using UV-LIGA compatible electroforming process has been performed. Single-walled carbon nanotubes (SWNTs) have been proven excellent mechanical properties and thermal conductive properties, such as high strength and elastic modulus, negative coefficient of thermal expansion (CTE) and a high thermal conductivity. These properties make SWNT an excellent reinforcement in nanocomposite for various applications. However, there has been a challenge of utilizing SWNTs for engineering applications due to difficulties in quality control and handling – too small (1-2nm in diameter). A novel copper/SWNT nanocomposite has been developed during this dissertational research. The goal of this research was to develop a heat spreader for high power electronics (HPE). Semiconductors for HPE, such as AlGaN/GaN high electron mobility transistors grown on SiC dies have a typical CTE about 4~6x10-6/k while most metallic heat spreaders such as copper have a CTE of more than 10x10-6/k. The SWNTs were successfully dispersed in the copper matrix to form the SWNT/Cu nano composite. The tested composite density is about 7.54 g/cm3, which indicating the SWNT volumetric fraction of 18%. SEM pictures show copper univformly coated on SWNT (worm-shaped structure). The measured CTE of the nanocomposite is 4.7 x 10-6/°C, perfectly matching that of SiC die (3.8 x 10-6/°C). The thermal conductivity derived by Wiedemann-Franz law after measuring composit's electrical conductivity, is 588 W/m-K, which is 40% better than that of pure copper. These properties are extremely important for the heat spreader/exchanger to remove the heat from HPE devices (SiC dies). Meanwhile, the matched CTE will reduce the resulted stress in the interface to prevent delaminations. Therefore, the naocomposite developed will be an excellent replacement material for the CuMo currently used in high power radar, and other HPE devices under developing. The mechanical performance and reliability of micro mechanical devices are critical for their application. In order to validate the design & simulation results, a direct (tensile) test method was developed to test the mechanical properties of the materials involved in this research, including nickel and SU-8. Micro machined specimens were fabricated and tested on a MTS Tytron Micro Force Tester with specially designed gripers. The tested fracture strength of nanostructured nickel is 900±70 MPa and of 50MPa for SU-8, resepctively which are much higher than published values.
Show less
Date Issued: 2005
Identifier: CFE0000478, ucf:46372
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0000478

Title: MICROSTRUCTURAL AND MECHANICAL CHARACTERIZATION OF AL-AL2O3 NANOCOMPOSITES SYNTHESIZED BY HIGH-ENERGY MILLING.
Creator: Prabhu, Balaji, Challapalli, Suryanarayana, University of Central Florida
Abstract / Description: The twin objectives of the investigation were (i) to synthesize Al/Al2O3 metal matrix composites (MMCs) with uniform distribution of the Al2O3 reinforcement in the Al matrix and (ii) to evaluate the effect of volume fraction and size of the reinforcement on the mechanical behavior of MMCs. This was achieved by successful synthesis of Al-Al2O3 MMCs with volume fractions of 5, 10, 20, 30, and 50%, and particle sizes of 50 nm, 150 nm, and 5 µm of Al2O3 synthesized from blended component...
Show moreThe twin objectives of the investigation were (i) to synthesize Al/Al2O3 metal matrix composites (MMCs) with uniform distribution of the Al2O3 reinforcement in the Al matrix and (ii) to evaluate the effect of volume fraction and size of the reinforcement on the mechanical behavior of MMCs. This was achieved by successful synthesis of Al-Al2O3 MMCs with volume fractions of 5, 10, 20, 30, and 50%, and particle sizes of 50 nm, 150 nm, and 5 µm of Al2O3 synthesized from blended component powders by a high-energy milling technique. A uniform distribution of the Al2O3 reinforcement in the Al matrix was successfully obtained after milling the powders for a period of 20 h with a ball-to-powder weight ratio of 10:1 in a SPEX mill. The uniform distribution of Al2O3 in the Al matrix was confirmed by characterizing these nanocomposite powders by scanning electron microscopy and X-ray mapping. The energy dispersive spectroscopy and X-ray diffraction techniques were employed to determine the composition and phase analysis, respectively. The milled powders were then consolidated for subsequent mechanical characterization by (i) magnetic pulse compaction (MPC) (ii) hot-isostatic pressing (HIP), (iii) vaccum hot pressing (VHP), and (iv) a combination of vaccum hot pressing and hot-isostatic pressing (VHP+HIP). However, successful consolidation of the powders to near-full density was achieved only through VHP+HIP for the 5 and 10 vol. % Al2O3 samples with 50 nm and 150 nm particle sizes. The fully dense samples were then subjected to mechanical characterization by compression testing and nanoindentation techniques. The strength and elastic modulus values obtained from compression testing showed an increase with increasing volume fraction and decreasing particle size of the reinforcement. The nanoindentation results were, however, contradictory, and the presence of residual stresses in the samples was attributed as the cause for the deviation in values.
Show less
Date Issued: 2005
Identifier: CFE0000727, ucf:46602
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0000727

Title: POLYMER-DERIVED CERAMICS: ELECTRONIC PROPERTIES AND APPLICATION.
Creator: xu, weixing, An, Linan, University of Central Florida
Abstract / Description: In this work, we studied the electronic behavior of polymer-derived ceramics (PDCs) and applied them for the synthesis of carbon nanotube reinforced ceramic nanocomposites and ceramic MEMS (Micro-Electro-Mechanical Systems) structures. Polymer-derived SiCN ceramics were synthesized by pyrolysis of a liquid polyureasilazane with dicumyl peroxide as thermal initiator. The structural evolution during pyrolysis and post-annealing was studied using FTIR, solid state NMR and Raman. The results...
Show moreIn this work, we studied the electronic behavior of polymer-derived ceramics (PDCs) and applied them for the synthesis of carbon nanotube reinforced ceramic nanocomposites and ceramic MEMS (Micro-Electro-Mechanical Systems) structures. Polymer-derived SiCN ceramics were synthesized by pyrolysis of a liquid polyureasilazane with dicumyl peroxide as thermal initiator. The structural evolution during pyrolysis and post-annealing was studied using FTIR, solid state NMR and Raman. The results revealed that the resultant ceramics consisted of SiCxNx-4 as major building units. These units were connected with each other through C-C/C=C bonds or by shearing N/C. The amount of sp2 free carbon strongly depends on composition and processing condition. Electron paramagnetic resonance (EPR) was used to investigate electronic structure of PDCs; the results revealed that the materials contain unpaired electron centers associated with carbons. Electronic behavior of the SiCN ceramics was studied by measuring their I-V curves, temperature dependence of d.c.-conductivities and impendence. The results revealed that the SiCN ceramics exhibited typical amorphous semiconductor behavior, and their conductivity varied in a large range. The results also revealed that the materials contain more than one phase, which have the different electronic behavior. We explored possibility of using polymer-derived ceramics to make ceramic MEMS for harsh environmental applications with a lithography technique. The cure depth of the polymer precursor was measured as a function of UV intensity and exposure time. The experimental data was compared with the available theoretical model. A few typical SiCN parts were fabricated by lithography technique. We also prepared carbon nanotube reinforced ceramic nanocomposites by using PDC processing. The microstructures of the composites were characterized using SEM and TEM; the mechanical properties were studied characterized using nanoindentation. The significant improvement in mechanical properties was observed for the nanocomposites.
Show less
Date Issued: 2006
Identifier: CFE0001228, ucf:46885
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0001228

Title: DEVELOPMENT AND APPLICATION STUDY OF NANOSCALE THIN FILM MATERIALS AND POLYMER NANOCOMPOSITES.
Creator: Chen, Hui, Huo, Qun, University of Central Florida
Abstract / Description: This dissertation demonstrated that the manipulation of substances at the molecular or nanometer level can lead to the discovery and development of new materials with interesting properties and important applications. Chapter 1 describes the development of a nanoscale molecular thin film material for corrosion protection. By using a self-assembled monolayer film with a thickness of only about 1 nanometer as a linkage, a covalent bonding was achieved between a polyurethane top coating and an...
Show moreThis dissertation demonstrated that the manipulation of substances at the molecular or nanometer level can lead to the discovery and development of new materials with interesting properties and important applications. Chapter 1 describes the development of a nanoscale molecular thin film material for corrosion protection. By using a self-assembled monolayer film with a thickness of only about 1 nanometer as a linkage, a covalent bonding was achieved between a polyurethane top coating and an aluminum alloy substrate. This covalent bonding between polymer top coating and the aluminum alloy substrate significantly improved the corrosion resistance of the substrate. Chapter 2 and Chapter 3 describe the development of a gold nanoparticle-polymer composite material in different forms with a number of applications. Gold nanoparticles are among one of the most extensively studied nanomaterials. When the size of gold is shrunk to the nanometer scale, many interesting and new physical properties start to appear from gold nanoparticles. The optical properties of gold nanoparticles, particularly the surface plasmon resonance absorption, have been investigated in this dissertation for the development of multifunctional nanocomposite materials. Chapter 2 presents the preparation of a gold nanoparticle/poly(methyl methacrylate) (PMMA) nanocomposite film and the application of such films for microstructure fabrication using a direct laser writing technique. Gold nanoparticles are excellent photon-thermal energy converters due to their large absorption cross section at the surface plasmon resonance region. Upon laser irradiation of the nanocomposite film, the thermal energy converted from the absorbed photon energy by gold nanopaticles induced a complete decomposition of PMMA, leading to the formation of various microstructures on the nanocomposite films. Chapter 3 reports the further development of a nanoparticle/polymer composite nanofiber material fabricated through an electrospinning process. The matrix of the nanofiber is made of two polyelectrolytes, poly(acrylic acid) (PAA) and poly(allylamine hydrochloride) (PAH). Three methods were developed to incorporate gold nanoparticles into the polymer matrix. The composite nanofiber materials developed in this study demonstrate multifunctional properties, including good electrical conductivity, photothermal response, and surface-enhanced IR absorption. This material may be used for many important applications including catalysis, chemical and biological sensors, and scaffold materials for tissue engineering. In Chapter 4, another most important nanomaterial, carbon naotubes (CNTs), were introduced as fillers to prepare polymer nanocomposites. A dispersion method for multi-walled carbon nanotubes (MWCNTs) using a conjugated conducting polymer, poly(3-hexylthiophene) (P3HT) as the third component and trifluoroacetic acid (TFA) as a co-solvent was developed. Due to the excellent dispersion of carbon nanotubes in PMMA and enhanced conductivity of the nanocomposites by the conjugated conducting polymers, the prepared composite materials has an extremely low percolation threshold of less than 0.006 wt% of MWCNT content. The potential use of MWCNT/conducting polymer composites for energy storage applications such as suppercapacitors was further investigated by Cyclic Voltammetry (CV), Electrochemical Impedance Spectroscopy (EIS) and charging-discharging cycles. Compared to pure carbon nanotubes, the nanocomposite materials have significantly improved properties and are promising for supercapacitor applications.
Show less
Date Issued: 2008
Identifier: CFE0002265, ucf:47825
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0002265

Title: SYNTHESIS AND APPLICATIONS OF RING OPENING METATHESIS POLYMERIZATION BASED FUNCTIONAL BLOCK COPOLYMERS.
Creator: Biswas, Sanchita, Belfield, Kevin, University of Central Florida
Abstract / Description: Ring opening metathesis polymerization (ROMP) is established as one of the efficient controlled living polymerization methods which have various applications in polymer science and technology fields. The research presented in this dissertation addresses several applications of multifunctional well-defined norbornene-based block copolymers synthesized by ROMP using ruthenium-based Grubbs catalysts. These novel block copolymers were applied to stabilize maghemite nanoparticles, creating the...
Show moreRing opening metathesis polymerization (ROMP) is established as one of the efficient controlled living polymerization methods which have various applications in polymer science and technology fields. The research presented in this dissertation addresses several applications of multifunctional well-defined norbornene-based block copolymers synthesized by ROMP using ruthenium-based Grubbs catalysts. These novel block copolymers were applied to stabilize maghemite nanoparticles, creating the superparamagnetic polymeric nanocomposites. The J-aggregation properties of the porphyrin dyes were improved via self-assembly with a customized norbornene polymer. Novel multimodal copolymer probes were synthesized for two-photon fluorescence integrin-targeted bioimaging. In Chapter 1 a brief overview of ROMP along with ruthenium metal catalysts and selected applications of the polymers related to this research is presented. Superparamagnetic maghemite nanoparticles are important in biotechnology fields, such as enhanced magnetic resonance imaging (MRI), magnetically controlled drug delivery, and biomimetics. However, cluster formation and eventual loss of nano-dimensions is a major obstacle for these materials. Chapter 2 presents a solution to this problem through nanoparticles stabiulized in a polymer matrix. The synthesis and chracterization of novel diblock copolymers, consisting of epoxy pendant anchoring groups to chelate maghemite nanoparticles and steric stabilizing groups, as well as generation of nanocomposites and their characterization, including surface morphologies and magnetic properties, is discussed in Chapter 2. In Chapter 3, further improvement of the nanocomposites by ligand modification and the synthesis of pyrazole-templated diblock copolymers and their impact to stabilize the maghemite nanocomposite are presented. Additionally, the organic soluble magnetic nanocomposites with high magnetizations were encapsulated in an amphiphilic copolymer and dispersed in water to assess their water stability by TEM. To gain a preliminary measure of biocopatibility of the micelle-encapsulated polymeric magnetic nanocomposites, cell-viability was determined. In Chapter 4, aggregation behaviors of two porphyrin-based dyes were investigated. A new amphiphilic homopolymer containing secondary amine moieties was synthesized and characterized. In low pH, the polymer became water soluble and initiated the stable J-aggregation of the porphyrin. Spectroscopic data supported the aggregation behavior. Two photon fluorescence microscopy (2PFM) has become a powerful technique in bioimaging for non-invasive imaging and potential diagnosis and treatment of a number of diseases via excitation in the near-infrared (NIR) region. The fluorescence emission upon two-photon absorption (2PA) is quadratically dependent with the intensity of excitation light (compared to the linear dependence in the case of one-photon absoprtion), offering several advantages for biological applications over the conventional one-photon absorption (1PA) due to the high 3D spatial resolution that is confined near the focal point along with less photodamage and interference from the biological tissues at longer wavelength (~700-900 nm). Hence, efficient 2PA absorbing fluorophores conjugated with specific targeting moieties provides an even better bioimaging probe to diagnose desired cellular processes or areas of interest The αVβ3 integrin adhesive protein plays a significant role in regulating angiogenesis and is over-expressed in uncontrolled neovascularization during tumor growth, invasion, and metastasis. Cyclic-RGD peptides are well-known antagonists of αVβ3 integrin which suppress the angiogenesis process, thus preventing tumor growth. In Chapter 5 the synthesis, photophysical studies and bioimaging is reported for a versatile norbornene-based block copolymer multifunctional scaffold containing biocompatible (PEG), two-photon fluorescent (fluorenyl), and targeting (cyclic RGD peptide) moieties. This water-soluble polymeric multi scaffold probe with negligible cytotoxicity exhibited much stronger fluorescence and high localization in U87MG cells (that overexpress integrin) compared to control MCF7 cells. The norbornene-based polymers and copolymers have quite remarkable versatility for the creation of advanced functional magnetic, photonic, and biophotonic materials.
Show less
Date Issued: 2010
Identifier: CFE0003065, ucf:48296
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003065

Title: PROCESSING, OPTIMIZATION AND CHARACTERIZATION OF FIRE RETARDANT POLYMER NANOCOMPOSITES.
Creator: Zhuge, Jinfeng, Gou, Jihua, University of Central Florida
Abstract / Description: Fiber reinforced polymeric composites (FRPC) have superior physical and mechanical properties, such as high specific strength, light weight, and good fatigue and corrosion resistance. They have become competitive engineering materials to replace conventional metallic materials in many important sectors of industry such as aircraft, naval constructions, ships, buildings, transportation, electrical and electronics components, and offshore structures. However, since FRPC contain polymer matrix,...
Show moreFiber reinforced polymeric composites (FRPC) have superior physical and mechanical properties, such as high specific strength, light weight, and good fatigue and corrosion resistance. They have become competitive engineering materials to replace conventional metallic materials in many important sectors of industry such as aircraft, naval constructions, ships, buildings, transportation, electrical and electronics components, and offshore structures. However, since FRPC contain polymer matrix, the polymer composites and their structures are combustible. FRPC will degrade, decompose, and sometimes yield toxic gases at high temperature or subject to fire conditions. The objective of this study is to design and optimize fire retardant nanopaper by utilizing the synergistic effects of different nanoparticles. A paper-making technique that combined carbon nanofiber, nanoclay, polyhedral oligomeric silsesquioxanes, graphite nanoplatelet, and ammonium polyphosphate into self-standing nanopaper was developed. The fire retardant nanopaper was further incorporated into the polymer matrix, in conjunction with continuous fiber mats, through resin transfer molding process to improve fire retardant performance of structural composites. The morphology, thermal stability, and flammability of polymer composites coated with hybrid nanopaper were studied. The cone calorimeter test results indicated that the peak heat release rate of the composites coated with a CNF-clay nanopaper was reduced by 60.5%. The compact char material formed on the surface of the residues of the CNF-clay nanopaper was analyzed to understand the fire retardant mechanism of the nanopaper. The financial support from Office of Naval Research is acklowdged.
Show less
Date Issued: 2010
Identifier: CFE0003151, ucf:48618
Format: Document (PDF)
PURL: http://purl.flvc.org/ucf/fd/CFE0003151

nanocomposites (7)	+ -
Nanocomposite (5)	+ -
Nanocomposites (4)	+ -
piezospectroscopy (3)	+ -
Alumina (2)	+ -

PDC (2)	+ -
carbon nanotube (2)	+ -
nanocomposite (2)	+ -
ASTM D4812 (1)	+ -
ASTM D6671 (1)	+ -
Aerosol (1)	+ -
Al-Al2O3 Nanocomposites (1)	+ -
Aluminum (1)	+ -
Bioimaging probe (1)	+ -
Block copolymer (1)	+ -
Buckypaper (1)	+ -
Carbon nanofiber (1)	+ -
Carbon nanotubes (1)	+ -
Ceria (1)	+ -
Chemical spray pyrolysis (1)	+ -
Coatings (1)	+ -
Computational fluid dynamics (1)	+ -
Electrical Property (1)	+ -
Electroforming (1)	+ -
Film growth (1)	+ -
Film processing (1)	+ -
Gas sensors (1)	+ -
J-aggregations (1)	+ -
Lithium-ion batteries (1)	+ -
MEMS (1)	+ -

University of Central Florida (23)	+ -
Gou, Jihua (7)	+ -
Raghavan, Seetha (4)	+ -
An, Linan (3)	+ -
Bai, Yuanli (3)	+ -

Fang, Jiyu (3)	+ -
Lin, Kuo-Chi (3)	+ -
Xu, Yunjun (3)	+ -
Challapalli, Suryanarayana (2)	+ -
Chen, Quanfang (2)	+ -
Coffey, Kevin (2)	+ -
Huo, Qun (2)	+ -
Orlovskaya, Nina (2)	+ -
Zhai, Lei (2)	+ -
Algozzini, Lee (1)	+ -
Bai, Jing (1)	+ -
Belfield, Kevin (1)	+ -
Biswas, Sanchita (1)	+ -
Chen, Hui (1)	+ -
Deng, Weiwei (1)	+ -
Divo, Eduardo (1)	+ -
Freihofer, Gregory (1)	+ -
Fugon-Dessources, Daniela (1)	+ -
Gibson, Jason (1)	+ -
Gou, Jan (1)	+ -
Harish, Muthuraman (1)	+ -
Ilegbusi, Olusegun (1)	+ -
Kalita, Samar (1)	+ -
Kassab, Alain (1)	+ -
Katiyar, Pushkar (1)	+ -

Search In

Pages

Pages

Sort Results By:

Narrow results by:

Topical Subject

Collection

Type of Resource

Language

Creator

Format

Owner