View All Items
(1 - 4 of 4)
- Title
- PROCESSING OF CUBIC STABILIZED ZIRCONIA ELECTROLYTE MEMBRANES FOR ELECTROLYTE-SUPPORTED SINGLE CELL SOLID OXIDE FUEL CELLS USING TAPE CASTING.
- Creator
-
Coronado Rodriguez, Arturo, Orlovskaya, Nina, University of Central Florida
- Abstract / Description
-
Electrochemical conversion devices are a developing technology that prove to be a viable and more efficient alternative to current environmentally friendly generation devices. As such, constant research has been done in the last few decades to increase their applications and reliability. One of these systems, and the focus of this research, is the single cell Solid Oxide Fuel Cell (SOFC). These systems are a developing technology which main caveat is the need of high operating temperatures...
Show moreElectrochemical conversion devices are a developing technology that prove to be a viable and more efficient alternative to current environmentally friendly generation devices. As such, constant research has been done in the last few decades to increase their applications and reliability. One of these systems, and the focus of this research, is the single cell Solid Oxide Fuel Cell (SOFC). These systems are a developing technology which main caveat is the need of high operating temperatures and costs. As such, most multidisciplinary research has been focused on researching materials and/or processes that help mitigate the costs or lower the operating temperature. The research presented in this paper focused on the manufacturing of a cubic stabilized zirconia (CSZ) electrolyte thin membrane for a single cell SOFC through tape casting. Thus, the process was divided into slurry preparation, tape casting, further processing, and analysis of samples. First the tape was produced reaching optimal viscosity (between 500 to 6000 cP) and minimizing impurities. Then, the slurry was poured into the doctor's blade with a 200 micrometers gap and allowed to dry. Samples were punched from the green tape with a diameter of 28 inches. Afterwards, these samples were pressed and sintered with a force of 218016 N and temperature of 1550 degrees celsius, respectively. These steps are done to maximize density and grain growth and minimize porosity. Lastly, the tape went further analysis and it was stated that further research should be done to determine this tape viability for stationary SOFC application.
Show less - Date Issued
- 2018
- Identifier
- CFH2000414, ucf:45838
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFH2000414
- Title
- Scandia and ceria stabilized zirconia based electrolytes and anodes for intermediate temperature solid oxide fuel cells: Manufacturing and properties.
- Creator
-
Chen, Yan, Orlovskaya, Nina, An, Linan, Chen, Quanfang, Sohn, Yongho, Raghavan, Seetha, Huang, Xinyu, University of Central Florida
- Abstract / Description
-
Scandia and ceria stabilized zirconia (10 mol% Sc2O3 (-) 1 mol% CeO2 (-) ZrO2, SCSZ) has superior ionic conductivity in the intermediate temperature range for the operation of solid oxide fuel cells, but it does not exhibit good phase stability in comparison with yttria stabilized zirconia (8 mol% Y2O3 (-) ZrO2, YSZ). To maintain high ionic conductivity and improve the stability of the electrolyte, layered structures with YSZ outer layers and SCSZ inner layers were designed, along with the...
Show moreScandia and ceria stabilized zirconia (10 mol% Sc2O3 (-) 1 mol% CeO2 (-) ZrO2, SCSZ) has superior ionic conductivity in the intermediate temperature range for the operation of solid oxide fuel cells, but it does not exhibit good phase stability in comparison with yttria stabilized zirconia (8 mol% Y2O3 (-) ZrO2, YSZ). To maintain high ionic conductivity and improve the stability of the electrolyte, layered structures with YSZ outer layers and SCSZ inner layers were designed, along with the referential electrolytes containing pure SCSZ or YSZ. The electrolytes were manufactured by tape casting, laminating, and pressureless sintering techniques. After sintering, while the thickness of YSZ outer layers remained constant at ~30 ?m, the thickness of inner layers of SCSZ for the 3-, 4- and 6-layer designs varied at ~30, ~60 and ~120 ?m, respectively. Selected characterizations were employed to study the structure, morphology, impurity content and the density of the electrolytes. Furthermore, in situ X-ray diffraction, neutron diffraction and Raman scattering were carried out to study the phase transition and lattice distortion during long-term annealing at 350 (&)deg;C and 275 (&)deg;C for SCSZ and YSZ, respectively, where the dynamic damping occurred when Young's modulus was measured.In YSZ/SCSZ electrolytes, thermal residual stresses and strains were generated due to the mismatch of coefficients of thermal expansion from each layer of different compositions. They could be adjusted by varying the thickness ratios of each layer in different designs of laminates. The theoretical residual stresses have been calculated for different thickness ratios. The effect of thermal residual stress on the biaxial flexural strength was studied in layered electrolytes. The biaxial flexure tests of electrolytes with various layered designs were performed using a ring-on-ring method at both room temperature and 800 (&)deg;C. The maximum principal stress during fracture indicated an increase of flexural strength in the electrolytes with layered structure at both temperatures in comparison with the electrolytes without compositional gradient. Such an increase of strength is the result of the existence of residual compressive stresses in the outer YSZ layer. In addition, Weibull statistics of the strength values were built for the layered electrolytes tested at room temperature, and the effect of thermal residual stresses on Weibull distribution was established. The calculation of residual stress present at the outer layers was verified. The high ionic conductivity was maintained with layered electrolyte designs in the intermediate temperature range. It was also established that the ionic conductivity of layered electrolytes exhibited 7% (-) 11% improvement at 800 (&)deg;C due to the stress/strain effects, and the largest improvements in a certain electrolyte was found to nearly coincide with the largest residual compressive strain in the outer YSZ layer.In addition to the study of layered electrolytes, mechanical properties of porous Ni/SCSZ cermet were studied. The anode materials were reduced by 65 wt% NiO (-) 35 wt% SCSZ (N65) and 50 wt% NiO (-) 50 wt% SCSZ (N50) porous ceramics in the forming gas. Young's modulus as well as strength and fracture toughness of non-reduced and reduced anodes has been measured, both at room and high temperatures. High temperature experiments were performed in the reducing environment of forming gas. It was shown that while at 700 (&)deg;C and 800 (&)deg;C the anode specimens exhibited purely brittle deformation, a brittle-to-ductile transition occurred at 800 (-) 900 (&)deg;C, and the anode deformed plastically at 900 (&)deg;C. Fractography of the anode specimens were studied to identify the fracture modes of the anodes tested at different temperatures.
Show less - Date Issued
- 2013
- Identifier
- CFE0005090, ucf:50750
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0005090
- Title
- SIZE-EFFECT OF PD NANOPARTICLES SUPPORTED ON ZRO2 IN THE CATALYTIC REDUCTION OF NO BY H2.
- Creator
-
Joh, YoungWoo, Roldan, Beatriz, University of Central Florida
- Abstract / Description
-
Size-selected Pd nanoparticles were synthesized by the reverse-micelle encapsulation method and deposited on a ZrO2 support for the catalytic NO reduction by H2. All of our samples were found to be highly selective, but a significant size effect was not seen for Pd nanoparticles of between 1.2 nm and 5.5 nm. Ultra-small Pd clusters of less than 1 nm were found to be much less active, and are assumed to be affected by an encapsulation effect of the support. Catalyst activity was comparable to...
Show moreSize-selected Pd nanoparticles were synthesized by the reverse-micelle encapsulation method and deposited on a ZrO2 support for the catalytic NO reduction by H2. All of our samples were found to be highly selective, but a significant size effect was not seen for Pd nanoparticles of between 1.2 nm and 5.5 nm. Ultra-small Pd clusters of less than 1 nm were found to be much less active, and are assumed to be affected by an encapsulation effect of the support. Catalyst activity was comparable to that of literature, and is applicable to H2-SCR research.
Show less - Date Issued
- 2011
- Identifier
- CFH0003863, ucf:44687
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFH0003863
- Title
- VIBRATIONAL AND MECHANICAL PROPERTIES OF 10 MOL % SC2O3-1 MOL % CEO2- ZRO2 ELECTROLYTE CERAMICS FOR SOLID OXIDE FUEL CELLS.
- Creator
-
Lukich, Svetlana, Orlovskaya, Nina, University of Central Florida
- Abstract / Description
-
Solid Oxide Fuel Cells (SOFCs) are emerging as a potential breakthrough energy conversion technology for clean and efficient production of electricity and heat from hydrogen and hydro-carbon fuels. Sc0.1Ce0.01ZrO2 electrolytes for Solid Oxide Fuel Cells are very promising materials because their high ionic conductivity in the intermediate temperature range 700oC-800oC. The vibration response of cubic and rhombohedral (β) 10 mol%Sc2O3 - 1 mol%CeO2 - ZrO2 (Sc0.1Ce0.01ZrO2 ) both at room...
Show moreSolid Oxide Fuel Cells (SOFCs) are emerging as a potential breakthrough energy conversion technology for clean and efficient production of electricity and heat from hydrogen and hydro-carbon fuels. Sc0.1Ce0.01ZrO2 electrolytes for Solid Oxide Fuel Cells are very promising materials because their high ionic conductivity in the intermediate temperature range 700oC-800oC. The vibration response of cubic and rhombohedral (β) 10 mol%Sc2O3 - 1 mol%CeO2 - ZrO2 (Sc0.1Ce0.01ZrO2 ) both at room and high-temperatures is reported. The in-situ heating experiments and ex-situ indentation experiments were performed to characterize the vibrational behavior of these important materials. A temperature and stress-assisted phase transition from cubic to rhombohedral phase was detected during in-situ Raman spectroscopy experiments. While heating and indentation experiments performed separately did not cause the transition of the cubic phase into the rhombohedral structure under the performed experimental conditions and only broadened or strained peaks of the cubic phase could be detected, the heating of the indented (strained) surface leaded to the formation of the rhombohedral Sc0.1Ce0.01ZrO2. Both temperature range and strained zone were estimated by in situ heating and 2D mapping, where a formation of rhombohedral or retention of cubic phase has been promoted. The mechanical properties, such as Young's modulus, Vickers hardness, indentation fracture resistance, room and high temperature four point bending strength and SEVNB fracture toughness along with the stress – strain deformation behavior in compression, of 10 mol% Sc2O3 – 1 mol % CeO2 - ZrO2 (ScCeZrO2) ceramics have been studied. The chosen composition of the ScCeZrO2 has very high ionic conductivity and, therefore, is very promising oxygen ion conducting electrolyte for the intermediate temperature Solid Oxide Fuel Cells. Therefore, its mechanical behavior is of importance and is presented in this study.
Show less - Date Issued
- 2009
- Identifier
- CFE0002914, ucf:52845
- Format
- Document (PDF)
- PURL
- http://purl.flvc.org/ucf/fd/CFE0002914
